Pioneer DEH-7200SD, Руководство по эксплуатации

Страница: 15 / 28

You can adjust the currently selected equalizer curve
setting as desired. Adjusted equalizer curve settings
are memorized in
Custom1 or Custom2 .
!
A separate
Custom1
curve can be created for
each source. If you make adjustments when a
curve other than
Custom2 is selected, the equali-
zer curve settings will be memorized in Custom1 .
!
A Custom2 curve can be created common to all
sources. If you make adjustments when the Cus-
tom2 curve is selected, the Custom2 curve will
be updated.
1
Recall the equalizer curve you want to adjust.
2
Push M.C. left or right to select the equalizer
band to adjust.
100Hz
—
315Hz
—
1.25kHz
—
3.15kHz
—
8kHz
3
Push M.C. up or down to adjust the equalizer
curve.
+6 to
–
6 is displayed as the equalizer curve is in-
creased or decreased.
LOUD (loudness)
Loudness compensates for deficiencies in the low-
and high-frequency ranges at low volume.
1
Press M.C. to turn loudness on or off.
2
Push M.C. left or right to select the desired set-
ting.
Low (low)
—
Mid (mid)
—
High (high)
—
OFF (off)
Sub W.1 (subwoofer on/off setting)
This unit is equipped with a subwoofer output which
can be turned on or off.
1
Press
M.C.
to turn subwoofer output on or off.
2
Push M.C. left or right to select the phase of sub-
woofer output.
Push
M.C.
left to select reverse phase and
Re-
verse appears in the display. Push M.C. right to
select normal phase and Normal appears in the
display.
Sub W.2
(subwoofer adjustment)
When the subwoofer output is on, you can adjust the
cut-off frequency and the output level of the subwoo-
fer.
Only frequencies lower than those in the selected
range are outputted from the subwoofer.
1
Push M.C. left or right to select cut-off frequency.
50Hz
—
63Hz
—
80Hz
—
100Hz
—
125Hz
2
Push M.C. up or down to adjust the output level
of the subwoofer.
Each time
M.C.
is pushed up or down, subwoofer
level increases or decreases. +6 to -24 is dis-
played as the level is increased or decreased.
Bass (bass boost)
1
Push M.C. up or down to select a desired level.
0
to
+6
is displayed as the level is increased or de-
creased.
HPF (high pass filter adjustment)
When you do not want low sounds from the subwoo-
fer output frequency range to play from the front or
rear speakers, turn on the HPF (high pass filter). Only
frequencies higher than those in the selected range
are output from the front or rear speakers.
1
Press
M.C.
to turn high pass filter on or off.
2
Push M.C. left or right to select cut-off frequency.
50Hz
—
63Hz
—
80Hz
—
100Hz
—
125Hz
SLA (source level adjustment)
SLA (Source level adjustment) lets you adjust the vo-
lume level of each source to prevent radical changes
in volume when switching between sources.
!
Settings are based on the FM volume level, which
remains unchanged.
Before adjusting source levels, compare the FM
volume level with the level of the source you wish
to adjust.
!
The MW/LW volume level can also be adjusted
with source level adjustments.
1
Push M.C. up or down to adjust the source vo-
lume.
Adjustment range:
+4 to
–
4
Note
When selecting FM as the source, you cannot
switch to
SLA .
Initial Settings
1
1
Function display
!
Shows the function status.
1 Press SRC/OFF and hold until the unit
turns off.
2 Press M.C. and hold until the initial set-
ting menu appears in the display.
Operating this unit
En
15
Section
02
Operating
this
unit