Pioneer DEH-6350SD, Руководство пользователя

Страница: 11 / 100

This unit
3 4 5 6 7
2 1
1 Front output
2
Rear output
3 Antenna input
4
Fuse (10 A)
5
Power cord input
6
Wired remote input
Hard-wired remote control adaptor can be
connected (sold separately).
7
Subwoofer output
Power cord
Perform these connections when not connect-
ing a rear speaker lead to a subwoofer.








1
8
9
c
d
6
3 2
4
5
7
a
b
e
f
h
g
L R
F
R
Perform these connections when using a sub-
woofer without the optional amplifier.










1
8
9
c
d
6
3 2
4
7
a
b
a
b
e
f
h
g
L R
F
SW
i
j
d
c
k l
1 To power cord input
2
Left
3
Right
4
Front speaker
5
Rear speaker
6 White
7
White/black
8
Gray
9
Gray/black
a
Green
b
Green/black
c
Violet
d Violet/black
e
Black (chassis ground)
Connect to a clean, paint-free metal location.
f
Yellow
Connect to the constant 12 V supply termi-
nal.
g
Red
Connect to terminal controlled by ignition
switch (12 V DC).
h
Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control ter-
minal (max. 300 mA 12 V DC).
i
Subwoofer (4
Ω
)
j
When using a subwoofer of 70 W (2
Ω
), be
sure to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and green/
black leads.
k
Not used.
l
Subwoofer (4
Ω
)× 2
Notes
!
With a 2 speaker system, do not connect any-
thing to the speaker leads that are not con-
nected to speakers.
!
Change the initial setting of this unit. Refer
to
SW CONTROL
(rear output and subwoofer
setting) on page 9.
The subwoofer output of this unit is monau-
ral.
Power amp (sold separately)
Perform these connections when using the op-
tional amplifier.












1
1
3
2
4
5 5
3
2
6
7 7
1
3
2
8
9 9
1 System remote control
Connect to Blue/white cable.
2
Power amp (sold separately)
3
Connect with RCA cables (sold separately)
4
To Rear output
5 Rear speaker
6
To Front output
7 Front speaker
8
To subwoofer output
9
Subwoofer
Installation
Important
!
Check all connections and systems before
final installation.
!
Do not use unauthorized parts as this may
cause malfunctions.
!
Consult your dealer if installation requires
drilling of holes or other modifications to the
vehicle.
!
Do not install this unit where:
—
it may interfere with operation of the vehicle.
—
it may cause injury to a passenger as a result
of a sudden stop.
!
The semiconductor laser will be damaged if
it overheats. Install this unit away from hot
places such as near the heater outlet.
!
Optimum performance is obtained when the
unit is installed at an angle of less than 60°.
60°
!
To ensure proper heat dispersal when using
this unit, make sure you leave ample space
behind the rear panel and wrap any loose ca-
bles so they are not blocking the vents when
installing the unit.
DIN front/rear mount
This unit can be properly installed using either
front-mount or rear-mount installation.
Use commercially available parts when instal-
ling.
English
Installation 03
11
Section
Installation
En
<YRD5332-A/S>11