Pioneer DEH-2450UB, Руководство пользователя

Страница: 4 / 104

2 Turn M.C. to switch to YES. Press M.C. to
select.
#
If you do not operate for 30 seconds, the set up
menu will not be displayed.
#
If you prefer not to set up at this time, turn M.C.
to switch to
NO
. Press to select.
If you select NO , you cannot set up in the set up
menu.
3 Perform the following procedures to set
the menu.
To proceed to the next menu option, you need to
confirm your selection.
CLOCK SET (setting the clock)
1
Turn M.C. to adjust hour.
2
Press M.C. to select minute.
3
Turn M.C. to adjust minute.
4
Press M.C. to confirm the selection.
FM STEP (FM tuning step)
Normally, the FM tuning step employed by seek
tuning is 50 kHz. When AF or TA is on, the tuning
step automatically changes to 100 kHz. It may be
preferable to set the tuning step to 50 kHz when
AF is on.
!
The tuning step remains at 50 kHz during man-
ual tuning.
1
Turn M.C. to select the FM tuning step.
50
(50 kHz)
—
100
(100 kHz)
2
Press M.C. to confirm the selection.
MW STEP
(MW tuning step)
The MW tuning step can be switched between
9 kHz and 10 kHz. When using the tuner in North,
Central or South America, reset the tuning step
from 9 kHz (531 kHz to 1 602 kHz allowable) to
10 kHz (530 kHz to 1 640 kHz allowable).
1
Turn M.C. to select the MW tuning step.
9
(9 kHz)
—
10
(10 kHz)
2
Press M.C. to confirm the selection.
DEMO (demo display setting)
1
Turn M.C. to set the demo display to on or off.
2
Press
M.C.
to confirm the selection.
QUIT appears.
4 To finish your settings, turn M.C. to select
YES. Press to select.
#
If you prefer to change your setting again, turn
M.C. to switch to NO . Press to select.
Notes
!
You can set up the menu options in the initial
settings. For details about the settings, refer
to
Initial settings on page 9.
!
You can cancel set up menu by pressing
SRC / OFF .
Basic operations
Important
!
Handle gently when removing or attaching
the front panel.
!
Avoid subjecting the front panel to excessive
shock.
!
Keep the front panel out of direct sunlight
and high temperatures.
!
To avoid damaging the device or vehicle inte-
rior, remove any cables and devices attached
to the front panel before detaching it.
Removing the front panel to protect your unit from
theft
1
Press the detach button to release the front
panel.
2
Push the front panel upward (
M
) and then pull
it toward (
N
) you.
3
Always keep the detached front panel in a pro-
tection device such as a protection case.
Re-attaching the front panel
1
Slide the front panel to the left.
Make sure to insert the tabs on the left side of
the head unit into the slots on the front panel.
2
Press the right side of the front panel until it is
firmly seated.
If you cannot attach the front panel to the
head unit successfully, make sure that you are
placing the front panel onto the head unit cor-
rectly. Forcing the front panel into place may
result in damage to the front panel or head
unit.
Turning the unit on
1
Press SRC / OFF to turn the unit on.
Turning the unit off
1
Press and hold SRC / OFF until the unit turns
off.
Selecting a source
1
Press SRC / OFF to cycle between:
TUNER
(tuner)
—
CD
(built-in CD player)
—
USB
(USB)/ iPod (iPod)
—
AUX (AUX)
Adjusting the volume
1
Turn M.C. to adjust the volume.
CAUTION
For safety reasons, park your vehicle when re-
moving the front panel.
Note
When this unit
’
s blue/white lead is connected to
the vehicle
’
s auto-antenna relay control termi-
nal, the vehicle
’
s antenna extends when this
unit
’
s source is turned on. To retract the anten-
na, turn the source off.
Use and care of the remote
control
Using the remote control
1
Point the remote control in the direction of the
front panel to operate.
When using for the first time, pull out the film
protruding from the tray.
Replacing the battery
1
Slide the tray out on the back of the remote
control.
2
Insert the battery with the plus (+) and minus
(
–
) poles aligned properly.
Operating this unit
4
Section
Operating this unit
En
02