51
Notice for the blue/white lead
When the ignition switch is turned on (ACC ON), a control signal
is output through the blue/white lead. Connect to an external
power amp’s system remote control terminal, the auto-aerial
relay control terminal, or the aerial booster power control termi-
nal (max. 300 mA 12 V DC). The control signal is output through
the blue/white lead, even if the audio source is switched off.
Important
When this product is in “
Power OFF
” mode, the control signal
is also turned off. If “
Power OFF
” mode is cancelled, the
control signal is output again and the aerial is extended with
the auto aerial function (if the aerial is being used). Be careful
so that the extended aerial does not come into contact with
any obstacles.
Rear panel (main terminals)
8
7
6
1
3
2
5
4
1
This product
2
Fuse (10 A)
3
Power supply
4
Aerial jack
5
Wired Remote Cable
Connect to steering wheel control interface of your vehicle.
For more details, consult your dealer.
6
Microphone 3 m
7
RGB cable (supplied with Hideaway TV tuner)
8
Hideaway TV tuner (GEX-1550TV (sold separately))
Power cord
1
2
3
4
5
6
7
8
9
a
b
c
b
d
1
To power supply
2
Power cord
3
Yellow
To terminal supplied with power regardless of ignition switch
position.
4
Red
To electric terminal controlled by ignition switch (12 V DC)
ON/OFF.
5
Orange/white
To lighting switch terminal.
6
Black (earth)
To vehicle (metal) body.
7
Violet/white
Of the two lead wires connected to the back lamp, connect
the one in which the voltage changes when the gear shift
is in the
REVERSE
(
R
) position. This connection enables
the product to sense whether the car is moving forwards or
backwards.
8
Yellow/black
If you use an equipment with Mute function, wire this lead
to the Audio Mute lead on that equipment. If not, keep the
Audio Mute lead free of any connections.
9
Blue/white
Connect to system control terminal of the power amp (max.
300 mA 12 V DC).
a
Light green
Used to detect the ON/OFF status of the handbrake. This
lead must be connected to the power supply side of the
handbrake switch.
b
Power supply side
c
Handbrake switch
d
Earth side
p
The position of the handbrake switch depends on the vehicle
model. For details, consult the vehicle Owner’s Manual or
dealer.
Speaker leads
1
2
9
a
d
e
7
4
3
5
6
8
b
c
L
R
F
R
1
To power supply
2
Power cord
3
Left
4
Right
5
Front speaker
6
Rear speaker
7
White
8
White/black
9
Grey
a
Grey/black
b
Green
or power amp (sold separately), make sure to connect
the earth wire first. Ensure that the earth wire is
properly connected to metal parts of the car’s body.
The earth wire of the power amp and the one of this
product or any other device must be connected to the
car separately with different screws. If the screw for
the earth wire loosens or falls out, it could result in
fire generation of smoke or malfunction.
Ground wire
Metal parts of car’s body
POWER AMP
Other devices
(Another electronic
device in the car)
When replacing the fuse, be sure to only use a fuse of
the rating prescribed on this product.
This product cannot be installed in a vehicle without ACC
(accessory) position on the ignition switch.
ACC
ON
S
T
A
R
T
O
FF
ON
S
T
A
R
T
O
FF
ACC position
No ACC position
To avoid short-circuiting, cover the disconnected lead with
insulating tape. It is especially important to insulate all
unused speaker leads, which if left uncovered may cause a
short circuit.
For connecting a power amp or other devices to this product,
refer to the manual for the product to be connected.
51
< CRD4941-A >
Connection
Connection
