Pioneer AVH-X8500BHS, Руководство пользователя

Страница: 47 / 228

Adjusting the response
positions of the touch panels
(Touch Panel Calibration)
If you feel that the touch panel keys on the
screen deviate from the actual positions that re-
spond to your touch, adjust the response posi-
tions of the touch panel. There are two
adjustment methods: four-point adjustment, in
which you touch four corners of the screen; and
16-point adjustment, in which you make fine-ad-
justments on the entire screen.
!
Park your car in a safe place and use this
function. Do not operate it while driving.
!
Touch the screen gently for adjustment.
Forcefully pressing the touch panel may
damage the touch panel. Do not use a sharp
pointed tool such as a ballpoint pen or me-
chanical pen. Doing so may damage the
screen.
!
If the touch panel cannot be adjusted prop-
erly, consult your local Pioneer dealer.
1 Turn the source off.
Refer to Turning the source ON/OFF on page 8.
2 Press and hold the home button to start
Touch Panel Calibration.
The four-point touch panel adjustment screen
appears. When two-point appears at once,
touch both.
3 Touch each of the arrows on the four cor-
ners of the screen.
#
To cancel the adjustment, press and hold the
home button.
4 Press the home button to complete four-
point adjustment.
Data for the adjusted position is saved.
#
Do not turn off the engine while the data is being
saved.
5 Press the home button to proceed to 16-
point adjustment.
The 16-point touch panel adjustment screen ap-
pears.
#
To cancel the adjustment, press and hold the
home button.
6 Gently touch the center of the + mark dis-
played on the screen.
After you touch all the marks, the data for the
adjusted position is saved.
#
Do not turn off the engine while the data is being
saved.
7 Press and hold the home button to com-
plete the adjustment.
Using an AUX source
An auxiliary device or portable device sold sepa-
rately can be connected to this unit.
About AUX connection methods
You can connect auxiliary devices to this unit.
Mini pin plug cable (AUX)
When connecting an auxiliary device using a mini
plug cable
iPods and portable audio/video players can be
connected to this unit via mini plug cable.
!
If an iPod with video capabilities is con-
nected to this unit via 3.5 mm plug (four
pole) cable (such as the CD-V150M), you can
enjoy the video contents of the connected
iPod.
!
A portable audio/video player can be con-
nected by using a 3.5 mm plug (four pole)
with an RCA cable (sold separately). How-
ever, depending on the cable, a reverse con-
nection between the red (right side audio)
cable and yellow (video) cable may be re-
quired in order for the sound and video
image to be reproduced correctly.
%
Insert the stereo mini plug into the AUX
input jack on this unit.
Refer to Connection on page 49.
Resetting the microprocessor
By pressing RESET , you can reset the microproc-
essor to its initial settings without changing the
bookmark information.
The microprocessor must be reset in the follow-
ing situations:
!
Before using this unit for the first time after
installation
!
If the unit fails to operate properly
!
When strange or incorrect messages appear
on the display
1 Turn the ignition switch OFF.
2 Press RESET with a pen tip or other
pointed instrument.
Refer to What
’
s what on page 7.
Note
Switch your engine ON or set the ignition switch
to ACC ON before pressing
RESET in the follow-
ing situations:
!
After completing connections
!
When erasing all stored settings
!
When resetting the unit to its initial (factory) set-
tings
English
Other functions
47
Section
Other functions
En
23
<YRD5376-A/N>47