Pioneer 2 / PeopleBot страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 78

background image

ActivMedia Robotics

The

MOTORS

button and its associated green LED are under software control. Normally,

your ActivMedia robot's motors are disabled when not connected with a client, such as

Navigator or Saphira. When first connected with a client,

9

the motors remain disabled

(LED flashes) until you press and release the

MOTORS

button. Pressing and releasing the

white

MOTORS

button then enables/disables the motors as long as the robot remains

connected with a client.

10

The green LED should light continuously when the motors are

enabled and blink

ON

and

OFF

when disengaged.

When not connected with a client, pressing and releasing the

MOTORS

button puts your

robot into joystick-drive mode. A subsequent press and release of the

MOTORS

button

puts the robot into Self-Test Mode that exercises the robot's drive, controller, and I/O

systems. See Chapter 5, Joydrive and Self-Test Modes, for details.

Press and hold the

MOTORS

button in combination with the

RESET

button to put the

microcontroller into a special system-download mode for reprogramming the onboard
FLASH ROM. See Pioneer 2 Operating System and Updating & Reconfiguring P2OS,

Chapter 6 and Chapter 7.

SERIAL

Your ActivMedia robot's microcontroller has two serial ports and three connectors. One
connector, labeled

SERIAL

, is a standard 9-pin D-SUB receptacle located on the

Console and is for direct RS232-compatible serial data communication between the

microcontroller and a client computer. This “Host” serial port shares its three-line
transmit, receive, and ground connections with one of the two serial connectors that is

inside the robot. See Appendix A for pinouts and cabling connections.

Amber LEDs on each side of the Host serial port light during data-exchange activity

transmitted from or received by the microcontroller.

Remove any tether or laptop connection from the Console SERIAL port

when using the optional radio modems.

RADIO

The

RADIO

slide switch on your robot’s Console controls power to the optional radio

modem or Ethernet radio. It does not affect the

SERIAL

port functions directly, but you

must switch the radio modem’s power

OFF

if you use the Console

SERIAL

port to

connect a piggyback laptop or another external computer to the robot.

The radio modem gets power as well as signals through the internal, shared Host serial
port and can interfere with Console

SERIAL

communications. In some cases, you may

have to physically remove the radio serial connection from the microcontroller to

eliminate that interference.

FLASH

A slide switch labeled

FLASH

is recessed into the Console. It write-protects the FLASH

ROM-stored P2OS software and your robot's operating parameters (see Updating and

Reconfiguring P2OS, Chapter 7). When switched forward, FLASH is enabled for writing.

ActivMedia’s P2OS maintenance utilities warn you if FLASH is disabled.

9

See the Quick Start chapter for client connection details.

10

A P2OS command also lets you toggle the motors under client control.

17

«
...
21
22
23
24
25
...
»

Содержание 2 / PeopleBot















































































Отзывы:

Нет отзывов

Похожие инструкции для 2 / PeopleBot

Бренд: RoboBuilder Страницы: 71

Бренд: DFRobot Страницы: 9

Бренд: ABB Страницы: 82

Бренд: ABB Страницы: 88

PickMaster Twin - PowerPac

Бренд: ABB Страницы: 454

Бренд: ABB Страницы: 234

Бренд: ABB Страницы: 230

Бренд: OnRobot Страницы: 84

Grove Infrared Emitter

Бренд: SeeedStudio Страницы: 4

Бренд: SuperDroid Robots Страницы: 9

IRB 8700 Series

Бренд: ABB Страницы: 848

Бренд: ABB Страницы: 64

Бренд: Raspberry Pi Страницы: 20

Бренд: XYZrobot Страницы: 46

Бренд: Keenon Robotics Страницы: 22

Бренд: ABB Страницы: 362

IRB 6700 - 150/3.20

Бренд: ABB Страницы: 846

Бренд: ABB Страницы: 360

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды