Pima PIMAGUARD, Инструкция по установке и эксплуатации

Страница: 55 / 62

Sentinel & PimaGuard
Installation Guide 55
In Atia External, the numbers continue as following:
In Atia External, zones/users higher than 97 are represented as space character (32 in Ascii as decimal).
* Alarm/Reset wildcard number means, that there is no difference in converting the values 1 or 3.
** 1 = E, 3 = R (CID, depending on the RS-232 protocol)
SIA
(Currently, event conversion is not available)
Zone\User Order
62-69 48, 49, 50, 51, 52, 53, 54, 55, 56, 57
70-79 97, 98, 99, 100, 101, 102, 103, 104, 105, 106
80-89 107, 108, 109, 110, 111, 112, 113, 114, 115, 116
90-96 117, 118, 119, 120, 121, 122, 65, 66, 67, 68
Data Code Short Description Long Description Address Field
AA Alarm – Panel
Substitution An attempt to substitute an alternate alarm panel for a secure
panel has been made Condition number
AB Abort An event message was not sent due to User action Zone or point
AN Analog Restoral An analog fire sensor has been restored to normal operation Zone or point
AR AC Restoral AC power has been restored Unused
AS Analog Service An analog fire sensor needs to be cleaned or calibrated Zone or point
AT AC Trouble AC power has been failed Unused
BA Burglary Alarm Burglary zone has been violated while armed Zone or point
BB Burglary Bypass Burglary zone has been bypassed Zone or point
BC Burglary Cancel Alarm has been cancelled by authorized user User number
BD Swinger Trouble A non-fire zone has been violated after a Swinger Shutdown on
the zone Zone or point
BE Swinger Trouble
Restore A non-fire zone restores to normal from a Swinger Trouble state Zone or point
BG Unverified Event -
Burglary A point assigned to a Cross Point group has gone into alarm but
the Cross Point remained normal Zone or point
BH Burglary Alarm
Restore Alarm condition eliminated Zone or point
BJ Burglary Trouble
Restore Trouble condition eliminated Zone or point
BM Burglary Alarm -
Cross Point Burglary alarm w/cross point also in alarm - alarm verified Zone or point
BR Burglary Restoral Alarm/trouble condition has been eliminated Zone or point
BS Burglary Supervisory Unsafe intrusion detection system condition Zone or point
BT Burglary Trouble Burglary zone disabled by fault Zone or point
BU Burglary Unbypass Zone bypass has been removed Zone or point
BV Burglary Verified A burglary alarm has occurred and been verified within
programmed conditions. (zone or point not sent) Area number
BX Burglary Test Burglary zone activated during testing Zone or point
BZ Missing Supervision A non-fire Supervisory point has gone missing Zone or point
CA Automatic Closing System armed automatically Area number
CD Closing Delinquent The system has not been armed for a programmed amount of
time Area number
CE Closing Extend Extend closing time User number
CF Forced Closing System armed, some zones not ready User number
CG Close Area System has been partially armed Area number
CI Fail to Close An area has not been armed at the end of the closing window Area number
CJ Late Close An area was armed after the closing window User number
CK Early Close An area was armed before the closing window User number
CL Closing Report System armed, normal User number
CM Missing Alarm-
Recent Closing A point has gone missing within 2 minutes of closing Zone or point
CO Command Sent A command has been sent to an expansion/peripheral device Condition number
CP Automatic Closing System armed automatically User number
CQ Remote Closing The system was armed from a remote location User number
CR Recent Closing An alarm occurred within five minutes after the system was
closed User number
CS Closing Keyswitch Account has been armed by keyswitch Zone or point
CT Late to Open System was not disarmed on time Area number
CW Was Force Armed Header for a force armed session, forced point msgs may follow Area number
CX Custom Function
Executed The panel has executed a preprogrammed set of instructions Custom Function
number
CZ Point Closing A point, as opposed to a whole area or account, has closed Zone or point
DA Card Assigned An access ID has been added to the controller User number
DB Card Deleted An access ID has been deleted from the controller User number
DC Access Closed Access to all users prohibited Door number
DD Access Denied Access denied, unknown code Door number
DE Request to Enter An access point was opened via a Request to Enter device Door number
DF Door Forced Door opened without access request Door number
DG Access Granted Door access granted Door number
DH Door Left Open -
Restoral An access point in a Door Left Open state has restored Door number