background image

PSEN cs5.1 M12/8

Operating Manual PSEN cs5.1 M12/8
1003419-EN-06

7

Safety regulations

Safety assessment

Before using a device it is necessary to perform a safety assessment in accordance with
the Machinery Directive.

Functional safety is guaranteed for the product as a single component. However, this does
not guarantee the functional safety of the overall plant/machine. In order to achieve the re-
quired safety level for the overall plant/machine, define the safety requirements for the
plant/machine and then define how these must be implemented from a technical and organ-
isational standpoint.

Additional documents that apply

Please read and take note of the following documents.

Only for use of the Safety Device Diagnostics (SDD):

}

Operating manual for the fieldbus module, for example SDD ES ETH or SDD ES
PROFIBUS

}

System description "Safety Device Diagnostics"

For the use of passive junctions:

}

Operating manual of a passive junction, for example:

PSEN ix2 F4 code

PSEN ix2 F8 code

PDP67 F 4 code

PSEN Y junction M12 sensor

PSEN Y junction M12 cable

You will need to be conversant with the information in these documents in order to fully un-
derstand this operating manual.

Use of qualified personnel

The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by competent persons.

A competent person is a qualified and knowledgeable person who, because of their train-
ing, experience and current professional activity, has the specialist knowledge required. To
be able to inspect, assess and operate devices, systems and machines, the person has to
be informed of the state of the art and the applicable national, European and international
laws, directives and standards.

It is the company’s responsibility only to employ personnel who

}

Are familiar with the basic regulations concerning health and safety / accident preven-
tion,

}

Have read and understood the information provided in the section entitled Safety

}

Have a good knowledge of the generic and specialist standards applicable to the spe-
cific application.

Содержание 542 009









































Отзывы: