PI MS249E Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 279

PI MS249E Скачать руководство пользователя страница 50

5 Installation

44

Version: 1.2.1

MS249E

C-863.12 Mercury Controller

✓

You have read and understood the user manual for the positioner.

Tools and accessories

▪

Positioner with DC motor and encoder with A/B quadrature signal transmission

▪

Suitable cable from the scope of delivery of the positioner

Connecting the positioner

1.

Connect the positioner to the C-863.12's

Motor

socket.

2.

Use the integrated screws to secure the connections against accidental disconnection.

5.5

Connecting the PC

Communication between the C-863.12 and a PC is required to configure the C-863.12 and to
command motion using the GCS commands. The C-863.12 has the following interfaces for this
purpose:

▪

RS-232 interface

▪

USB interface

In this section, you learn how to establish proper cable connections between the C-863.12 and
a PC and in a daisy chain network. The steps for establishing communication between C-863.12
and PC are described in the section "Startup":

▪

"Establishing Communication via RS-232" (p. 55)

▪

"Establishing Communication via USB" (p. 56)

▪

"Establishing Communication for Networked Controllers" (p. 58)

INFORMATION

Using a daisy chain network, up to 16 controllers can be connected to the PC via a single RS-
232 or USB connection.

5.5.1

Connecting to the RS-232 Interface

NOTICE

Incorrect wiring!

Connecting the USB and RS-232 interfaces of the controller to the PC at the same time can
damage the PC or the controller.

➢

Connect either the USB or the RS-232 interface to the PC.

«
...
48
49
50
51
52
...
»

Содержание MS249E
























































































































































































































































































Отзывы:

Нет отзывов