PI M-232.17 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 51

PI M-232.17 Скачать руководство пользователя страница 19

5 Installation

M-232 Linear Actuator

MP105E

Version: 1.2

15

5.1 General Notes on Installation

NOTICE

Cable break!

A cable break leads to a failure of the linear actuator.



Install the linear actuator so that the cable is not bent or squeezed too severely

during operation.

NOTICE

Increased friction!

Lateral forces that affect the pusher of the linear actuator increase the friction on the
internal drive components. Increased friction impairs the motion of the pusher and
increases wear on the drive components.



Avoid lateral forces on the pusher of the M-232.

NOTICE

Heating up of the M-232 during operation!

The heat produced during operation of the M-232 can affect your application.



Install the M-232 so that your application is not affected by the dissipating heat.

INFORMATION

Linear actuators with DC gear motors are equipped with integrated signal drivers for

cable lengths of

≤

10 m between linear actuator and motor controller.

INFORMATION

5

Installation

«
...
17
18
19
20
21
...
»

Содержание M-232.17




















































Отзывы:

Нет отзывов