PI M-230 Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 47

PI M-230 Series Скачать руководство пользователя страница 19

5 Installation

M-230 Linear Actuators

MP102E

Version: 1.2

15

5.1 General Notes on Installation

NOTICE

Cable break!

A cable break leads to a failure of the linear actuator.



Install the linear actuator so that the cable is not bent or squeezed too severely

during operation.

NOTICE

Increased friction!

Lateral forces that affect the pusher of the linear actuator increase the friction on the
internal drive components. Increased friction impairs the motion of the pusher and
increases wear on the drive components.



Avoid lateral forces on the tip and on the pusher of the M-230.

NOTICE

Heating up of the M-230 during operation!

The heat produced during operation of the M-230 can affect your application.



Install the M-230 so that your application is not affected by the dissipating heat.

INFORMATION

Models with DC gear motors are equipped with integrated signal drivers for cable

lengths

≤

10 m between the linear actuator and the motor controller.

5

Installation

«
...
17
18
19
20
21
...
»

Содержание M-230 Series
















































Отзывы:

Нет отзывов