manualshive.com logo in svg

Phytec 1488.2, Руководство по оборудованию

Поделиться
Скачать
Phytec 1488.2 Скачать руководство пользователя страница 48

PCM-065/phyCORE-i.MX8X System on Module 

 

 L-864e.A1 

 

 

 

 

 

© PHYTEC America LLC, 2021 

 

48 

Table 33.  UART Connections at the phyCORE-Connector 

X1 Pin #  Processor Signal 

SOM Signal 

Type 

Level 

Processor 
Ball 

Description 

A42 

UART0_CTS_B 

X_FLEXCAN0_RX 

I 

3.3V 

T22 

UART0 Clear to Send 

A41 

UART0_RTS_B 

X_FLEXCAN0_TX 

O 

3.3V 

U25 

UART0 Request to Send 

A49 

UART0_RX 

X_UART0_RX 

I 

3.3V 

V28 

UART0 Receive Data 

A48 

UART0_TX 

X_UART0_TX 

O 

3.3V 

U23 

UART0 Transmit Data 

A57 

UART1_CTS_B 

X_UART1_CTS_B 

I 

3.3V 

G27 

UART1 Clear to Send 

A58 

UART1_RTS_B 

X_UART1_RTS_B 

O 

3.3V 

G29 

UART1 Request to Send 

A59 

UART1_RX 

X_UART1_RX 

I 

3.3V 

E29 

UART1 Receive Data 

A60 

UART1_TX 

X_UART1_TX 

O 

3.3V 

J25 

UART1 Transmit Data 

A50 

UART2_RX 

X_UART2_RX 

I 

3.3V 

AD34 

UART2 Receive Data 

A51 

UART2_TX 

X_UART2_TX 

O 

3.3V 

AC35 

UART2 Transmit Data 

C61 

M40_UART0_RX 

X_SCU_GPIO0_00 

I 

1.8V 

Y22 

M4 UART0 Receive Data 

C62 

M40_UART0_TX 

X_SCU_GPIO0_01 

O 

1.8V 

AC25 

M4 UART0 Transmit Data 

C61 

SCU_UART0_RX 

X_SCU_GPIO0_00 

I 

1.8V 

Y22 

SCU UART0 Receive Data 

C62 

SCU_UART0_TX 

X_SCU_GPIO0_01 

O 

1.8V 

AC25 

SCU UART0 Transmit Data 

6.10

 

USB 

The  phyCORE-i.MX8X  SOM  provides  two  Universal  Serial  Bus  ports;  one  SuperSpeed  USB3.0  subsystem 
(USB0) and one HighSpeed USB2.0 subsystem (USB1). 

USB0  has been specified as both  USB 3.0 dual role and USB 2.0 On-The-Go (OTG) compatible. The USB0 
controller supports two independent USB cores (1× USB3.0 dual-role, 1× USB2.0 OTG) and includes the PHY 
and  I/O  interfaces  to  support  this  operation.  The  USB  2.0  module  is  compliant  with  On-The-Go  (OTG) 
supplement and the USB 3.0 is compliant with the USB 3.0, and USB 2.0 with OTG supplement specification. 

USB1 is a separate, independent USB 2.0 OTG controller which can be used simultaneously with USB 3.0. 

The full pinout of the USB 3.0 controller includes the signaling for both USB 3.0 and USB 2.0. This means that 
USB0 can be used as either a USB 3.0 port or a USB 2.0 port. USB1 can be used as a USB 2.0 port only and 
operates independently. So overall you can either have two USB 2.0 ports, or one USB 3.0 port and one USB 
2.0 port. 

Table 34.  USB0 SS3 Connections at the phyCORE-Connector 

X1 Pin #  SOM Signal 

Type  Level 

Processor Ball 

Description 

B7 

X_USB3_SS3_TC0 

I/O 

3.3V 

F14 

USB3 Super Speed 3 Transmission Control 0 

B8 

X_USB3_SS3_TC1 

I/O 

3.3V 

H14 

USB3 Super Speed 3 Transmission Control 1 

B10 

X_USB3_SS3_TC2 

I/O 

3.3V 

G15 

USB3 Super Speed 3 Transmission Control 2 

B11 

X_USB3_SS3_TC3 

I/O 

3.3V 

C15 

USB3 Super Speed 3 Transmission Control 3 

B13 

X_USB3_SS3_TX_P 

O 

Differential 

B16 

USB3 Super Speed 3 Transmit Data Positive 

B14 

X_USB3_SS3_TX_N 

O 

Differential 

A15 

USB3 Super Speed 3 Transmit Data 
Negative 

B16 

X_USB3_SS3_RX_P 

I 

Differential 

A19 

USB3 Super Speed 3 Receive Data Positive 

B17 

X_USB3_SS3_RX_N 

I 

Differential 

B18 

USB3 Super Speed 3 Receive Data Negative 

 

Table 35.  USB0 OTG Connections at the phyCORE-Connector 

X1 Pin #  SOM Signal 

Type 

Level 

Processor Ball  Description 

A1 

X_USB_OTG1_VBUS 

A/I 

5V 

H18 

USB OTG1 VBUS input 

A6 

X_USB_OTG1_ID 

A/I 

3.3V 

G17 

USB OTG1 2.0 Dual-Role Device Role Select 

A3 

X_USB_OTG1_DP 

I/O 

Differential 

D18 

USB OTG1 2.0 Differential Data Positive 

Содержание 1488.2































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды