Phoenix Advanced pressure monitor II Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 46

background image

Advanced Pressure Monitor II Rough-In Installation

Installation Overview

5

MKT-0262 MPC-1748 Rev 02/13

APM2 Rough-In Installation Guide

If an external sensor will be used then run the pressure signals (room and reference) to the remote transducer.

Figure 1-3.

Pressure Pickup Port Installation

1.3.4 Use of External Transducers

The APM2 has the option to use the internal pressure sensor or external pressure transducers (ordered
separately). If external pressure sensors are being used then no tubing needs to be run into the electrical box.
Instead the remote pressure transducer will be separately mounted, plumbed and wired. Only the wire for the
analog output of that transducer(s) will be run to the APM2. If two rooms are being monitored, you have the
choice to use the internal pressure sensor and an external (remote) transducer for the second room, or two
external remote transducers may be used and wired to the analog inputs in the back of the unit.

NOTE:

See Phoenix Recommended Cables

on page 33 for approved cable manufacturers and wire types.

Layout the system in terms of wiring:

•

Power: 24 Vac, 9 VA

•

Annunciator/relay: remote alarm wiring if being used

•

Analog output: 0-5 or 0-10 Vdc or 4-20 mA.

•

Analog Input wiring: there are two analog inputs that can be used to bring signals from remote pressure
transducers

•

Digital Input: the digital input can be used as a door status indication, these would be wired to a door switch
mounted in the door jamb.

Once the installation has been planned, locate and mount the electrical box and bring all tubing, power, earth
ground, analog input, digital input, relay/annunciator, analog output communications wiring into the triple
gang box.

«
...
7
8
9
10
11
...
»

Содержание Advanced pressure monitor II















































Отзывы:

Нет отзывов

Похожие инструкции для Advanced pressure monitor II

Бренд: Accuniq Страницы: 53

Бренд: TANDBERG Страницы: 64

SyncMaster VC240

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 2

Бренд: Datavideo Страницы: 14

Бренд: Valeo Страницы: 124

SyncMaster 2023 NW

Бренд: Samsung Страницы: 68

SyncMaster 720B

Бренд: Samsung Страницы: 78

Бренд: Garmin Страницы: 6

Бренд: Hanns.G Страницы: 1

DPLUS 74SB -BKB

Бренд: Mitsubishi Страницы: 176

Бренд: Samsung Страницы: 2

Бренд: Eizo Страницы: 2

Бренд: Wachendorff Страницы: 15

Бренд: Feelworld Страницы: 10

Бренд: NewLine Страницы: 86

Бренд: Viotek Страницы: 20

MediaMaster I05

Бренд: JL Audio Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды