background image

3. Turn the airplane upside down. Place your fingers 

on the masking tape and carefully lift the plane.

4.  If the nose of the plane falls, the plane is nose 

heavy. To correct this first move the battery pack 

further back in the fuselage. If this is not possible 

or does not correct it, stick small amounts of lead 

weight on the fuselage under the horizontal 

stabilizer. If the tail of the plane falls, the plane is 

tail heavy. To correct this, move the battery and 

receiver forward or if this is not possible, stick 

weight into the firewall. When balanced correctly, 

the airplane should sit level or slightly nose down 

when you lift it up with your fingers. 

BALANCING

1. It is critical that your airplane be balanced correctly. 

Improper balance will cause your plane to lose 

control and crash.

  THE CENTER OF GRAVITY IS LOCATED 141mm 

(5.5 in)  BACK FROM THE LEADING EDGE OF 

THE WING, AT THE FUSELAGE. BALANCE A 

PLANE UPSIDE DOWN WITH THE FUEL TANK 

EMPTY.

2.  Mount the wing to the fuselage. Using a couple of 

pieces of masking tape, place them on the top 

side of the wing 141mm (5.5 in) back from the 

leading edge, at the fuselage sides.

CONTROL THROWS

1. We highly recommend setting up a plane using 

the control throws listed.

2.  The control throws should be measured at the 

widest point of each control surface.

3.  Check to be sure the control surfaces move in 

the correct directions.

!

LATERAL BALANCE

    

After you have balanced a plane on the C.G. 

You should laterally balance it. Doing this will 

help the airplane track straighter.

1. Turn the airplane upside down. Attach one loop 

of heavy string to the engine crankshaft and 

one to the tail wheel wire. With the wings level, 

carefully lift the airplane by the string. This may 

require two people to make it easier.

2.  If one side of the wing fall, that side is heavier 

than the opposite. Add small amounts of lead 

weight to the bottom side of the lighter wing 

half's wing tip. Follow this procedure until the 

wing stays level when you lift the airplane.

Aileron     12mm up 

12mm down

Elevator     12mm up 

12mm down

Rudder     30mm right 

30mm left

Flap 

   25-35mm down

Low rate:

TUCANO 60CC

Instruction Manual

37

141mm 

(5.5 in)

Содержание TUCANO 60CC













































Отзывы: