background image

INSTALLING THE AILERONs SERVOS

1.  Install the rubber grommets and brass eyelets onto 

the aileron servo.

2. Using a modeling knife, remove the covering from over 

the pre-cut servo arm exit hole on the aileron servo 

tray / hatch. This hole will allow the servo arm to pass 

through when installing the  aileron pushrods.

3.  Place the servo into the servo tray. Center the servo 

within the tray and drill pilot holes through the block 

of wood for each of the four mounting screws 

provided with the servo.

4.  Using the thread as a guide and using masking 

tape, tape the servo lead to the end of the 

thread: carefully pull the thread out. When you 

have pulled the servo lead out, remove the 

masking tape and the servo lead from the 

thread.

5. Place the aileron servo tray / hatch into the servo 

box on the bottom of the wing and drill pilot 

holes through the tray and the servo box for 

each of the four mounting screws. Secure the 

servo tray in place using the mounting screws 

provided .

6. Repeat step # 2 - # 5 to install the second aileron 

servo in the opposite wing half.

Make certain the hinges are adequately secured with glue. If 

they come loose in flight accidents may result.

Secure nylon hinges with instant glue, being careful 

not to glue the wing and airleron together.

Apply instant glue (CA glue, super glue).

Align the center line of main wing with aileron.

Cut away film only. here

Supplied with the servo

approx. 13mm

2mm

Must be purchased

separately!
Assemble left and right

sides the same way

TIGER MOTH

Instruction Manual

2

Cut off shaded portion

< Bottom view >

Aileron

Содержание Tiger Moth









































Отзывы: