Phoenix Model P40 KITTY HAWK Скачать руководство пользователя страница 2

Страница: 2 / 20

P40 KITTY HAWK

Instruction Manual

Thank you for purchasing Phoenix Model products.

With over 20 years experience in production and fly testing,

Phoenix Model is committed to bring the best quality products and good service to customers. Along with a team of
creative engineers and skilled workers, we will always accompany with customers by our great experiences, fully
enthusiasm... which will burn our passion!! Joining with us to explore and conquer challenges in the sky ...
Your satisfaction is our success.

Please read through this manual before starting construction.

Academy of Model Aeronautics

5151 East Memorial Drive Muncie, IN 47302-9252

Tele. (800) 435-9262

Fax (765) 741-0057

Academy of Model Aeronautics:

If you are not already a member of the AMA, please join! The AMA is the

governing body of model aviation and membership provides liability insurance coverage, protects modelers’
rights and interests and is required to fly at most R/C sites.

TABLE OF CONTENTS

INTRODUCTION

Or via the Internet at: http://www.modelaircraft.org

....................................................

........................................................

......................................................

............................................

....................................

.....................................................

................................................

.................................................

.............................

..................................

...................................................

............................

....................

..................

.............................

................................

........................................

........................

..............................

.......................

Introduction

Warranty

Disclaimer

Safety precaution

Important building notes

Suggestion

Flight warnings

Covering tools

Adhesives and required tools

Academy of model aeronautics national

model aircraft safety code

Preparations

Installing the ailerons and flap

Installing the aileron and flap servos

Installing the control horns for aileron

Installing the control for flaps

Installing the flaps linkages

Superlock air retracts

Installing the horizontal stabilizer

Vertical stabilizer installation

.............................

Installing the aileron linkages

..........................

Installing the main landing gear

..............................................

................................

..................

.........................................

...........................

.................................

...........................................................

...........................

................................................

.............................

............................

.............................

.......................................................

.........................................

.......................

...............................................

Servo installation

Installing the fuselage servos

Installing the throttle pushrod housing

Installing the engine

Installing the motor and battery

Installing the electric motor

Fuel tank

Installing the stopper assembly

Installing the elevator pushrod

Engine installation

Installing the engine mount

Installing the rudder pushrod

...........................

Installing the control air system

...................................................

Final assembly

........................................

Installing the spinner

.................................................

.......................

.............................

......................................

Installing the throttle

Installing the receiver and battery

..................................

Installing the plastic bomb

..................................

Open and close the canopy

For your radio installation

Basic connection for airplane

Flight preparation pre flight check

Balancing

Lateral balance

Control throws

Assemble and install the tail gear

Содержание P40 KITTY HAWK





















Результаты поиска

Содержание P40 KITTY HAWK

Отзывы:

Похожие инструкции для P40 KITTY HAWK

Бренды по названию

Популярные бренды

Phoenix Model P40 KITTY HAWK, Инструкция по эксплуатации

Результаты поиска

Содержание P40 KITTY HAWK

Отзывы:

Похожие инструкции для P40 KITTY HAWK

Бренды по названию

Популярные бренды