Phoenix Model P40 KITTY HAWK Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 20

background image

22

23

9

INSTALLING THE HORIZONTAL STABILIZER

1. Using a modeling knife, cut away the covering from

the fuselage for the stabilizer and remove it.

24

7. Retract door cover.

8. Trim the retract door cover.

9. Secure the retract door cover.

21

19

20

5. Secure the air retract to the wing.

6. Install and secure the retract gear into the wing.

P40 KITTY HAWK

Instruction Manual

Remover the covering

Screw

25

Screw

Screw

2. Check the fit of the horizontal stabilizer in its

slot. Make sure the horizontal stabilizer is
square and centered to the fuselage by taking
measurements, but don't glue anything yet.

3. With the horizontal stabilizer correctly aligned,

mark the shape of the fuselage on the top and
bottom of the tail plane using a water soluble /
non-permanent felt-tip pen.

«
...
8
9
10
11
12
...
»

Содержание P40 KITTY HAWK





















Отзывы:

Нет отзывов

Похожие инструкции для P40 KITTY HAWK

Albatross D III

Бренд: REVELL Страницы: 6

Бренд: E sky Страницы: 80

Бренд: MAC Rail Страницы: 8

Бренд: H-KING Страницы: 12

Бренд: Faller Страницы: 8

Бренд: Fisher-Price Страницы: 28

Бренд: Stevens Aero Model Страницы: 31

Бренд: WM aerobatics Страницы: 8

Color Bilingual Laptop Plus

Бренд: Startright Страницы: 28

A6M3 Zero Type 32 landing flaps

Бренд: Eduard Страницы: 2

Бренд: Faller Страницы: 4

KID’Sleep My Dream

Бренд: Claessens' Kids Страницы: 5

Бренд: Force RC Страницы: 28

Бренд: Dynaflite Страницы: 42

Бренд: marklin Страницы: 2

Бренд: Accucraft Страницы: 9

Бренд: ACME Страницы: 9

Zoopa 150 Blu iz

Бренд: ACME Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды