background image

3

2

CA glue

5.  Apply six drops of thin CA to the top and bottom 

of each hinge. Do not use CA accelerator. After 
the CA has fully hardened, test the hinges by 
pulling on the aileron.

3.  Place the servo into the servo tray. Center the 

servo within the tray and drill 1,6mm pilot holes 
through the block of wood for each of the four 
mounting screws provided with the servo.

Remove the covering

3

INSTALLING THE AILERON SERVOS

1.  Install the rubber grommets and brass eyelets 

onto the aileron servo.

2. Using a modeling knife, remove the covering 

from over the pre-cut servo arm exit hole on the 
aileron servo tray / hatch. This hole will allow 
the servo arm to pass through when installing 
the  aileron pushrods.

4

6. Repeat step # 2 - # 5 to install the second 

aileron servo in the opposite wing half. 

5. Place the aileron servo tray / hatch into the 

servo box on the bottom of the wing and drill 
1,6mm pilot holes through the tray and the 
servo box for each of the four mounting screws. 
Secure the servo tray in place using the 
mounting screws provided ( 2mm x 12mm ).

7.  Using masking tape, tape the servo leads on to 

the top of the wing.

4.  Using the thread as a guide and using masking 

tape, tape the servo lead to the end of the 
thread: carefully pull the thread out. When you 
have pulled the servo lead out, remove the 
masking tape and the servo lead from the 
thread.

Servo lead

5

6

To the cowl

7

To the cowl

Содержание K8B















Отзывы: