Phoenix Contact IOL MA8 PN DI8 Скачать руководство пользователя страница 7

Страница: 7 / 84

Description

4022_en_A

PHOENIX CONTACT

Description

2.1

Overview

The IOL MA8 PN DI8 provides the ability to configure up to eight IO-Link sensors using web-

based management and seamlessly integrates your IO-Link devices into your control

system using Modbus TCP, PROFINET, and OPC UA.

2.2

Structure

The IOL MA8 PN DI8 features two Ethernet ports, status LEDs, and connectors for power

and IO-Link ports.

Figure 2-1

IOL MA8 PN DI8 structure

Table 2-1

IOL MA8 PN DI8 structure

Item

Description

Power connector

Port 1 IO-Link connector

Port 2 IO-Link connector

Port 3 IO-Link connector

Port 4 IO-Link connector

Port 5 IO-Link connector

Port 6 IO-Link connector

Port 7 IO-Link connector

Port 8 IO-Link connector

C/Q

MOD

4, 5

Содержание IOL MA8 PN DI8





















































































Результаты поиска

Содержание IOL MA8 PN DI8

Отзывы:

Бренды по названию

Популярные бренды

Phoenix Contact IOL MA8 PN DI8, Руководство пользователя

Результаты поиска

Содержание IOL MA8 PN DI8

Отзывы:

Бренды по названию

Популярные бренды