Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 72

Страница: 72 / 112

IB IL 24 PSDO 8-PAC

72 / 112

PHOENIX CONTACT

7619_en_05

Acknowledge all errors that are present. Only then can the outputs be re-enabled.

Acknowledgment: Yes (1)

Acknowledging the diagnostic message deletes the message. The module can only be re-

started following power up and error-free selftest.

Acknowledgment: Yes (2)

Acknowledging the diagnostic message deletes the message and enables a restart. Follow-

ing successful acknowledgment, the module also expects a positive edge from the applica-

tion for the output.

8.2

Supply voltage errors

Acknowledgment: Yes (1)

Acknowledging the diagnostic message deletes the message and activates the outputs.

Undervoltage at U

Supply voltage U

is measured. A diagnostics message is generated for U

< 17 V.

WARNING: Unexpected machine startup

An operator acknowledgment leads to a positive edge and can therefore result in the out-

puts being re-enabled.

INTERBUS-Safety

: Diagnostic message 002x

hex

(“The shutdown time parameterized for

the output was exceeded”) is also deleted in the event of a bus reset.

Table 8-2

Supply voltage U

errors

Error cause

Error Code

(Hex)

LED

Comment

Effect

Remedy

Acknow

ledgme

Undervoltage

01F0

flashing

below the per-

missible voltage

range

All module outputs

are in the safe state

Check supply volt-

age level and correct

Check supply line

length and load

Yes (1)

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 72 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: