Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 56

Страница: 56 / 112

IB IL 24 PSDO 8-PAC

56 / 112

PHOENIX CONTACT

7619_en_05

6.2

Notes on the protective circuit for external re-

lays/contactors (freewheeling circuit)

Figure 6-1

Example of the freewheeling circuit for an external relay

For all examples, please also observe the measures specified in the individual tables,

which must be taken to achieve the specified SIL/SILCL/Cat./PL and all measures accord-

ing to standards EN 61508, EN 62061, and EN ISO 13849-1 to achieve the specified

SIL/SILCL/Cat./PL.

WARNING: Disregarding this warning may lead to the loss of the safety function

An external voltage may not be supplied in an output (e.g., via cross-circuits). These er-

rors can adversely affect the operation of the module (or even destroy the module) and

therefore result in the loss of the safety function. Therefore, these errors must be prevent-

ed. Install the connecting cables for connecting the actuators so that they are protected

against cross-circuits.

Please observe the load capacity of the outputs according to the technical data in “Safe

digital outputs” on page 20.

–

Limit the voltage induced on circuit interruption to < -15 V (e.g., with RC elements,

suppressor diodes or varistors).

–

Please note that the freewheeling circuit affects the fall time and the service life of the

contactor.

–

Please observe the specifications of the relay manufacturer when sizing the relay pro-

tective circuit.

K 1

6 9 4 0 0 0 2 1

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 56 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: