Phoenix Contact IB IL 24 PSDO 8-PAC Скачать руководство пользователя страница 39

Страница: 39 / 112

Mounting, removal, and electrical installation

7619_en_05

PHOENIX CONTACT

39 / 112

Mounting, removal, and electrical installation

4.1

Mounting and removal

4.1.1

Unpacking the module

The module is supplied in an ESD box together with a packing slip with installation instruc-

tions. Please read the complete packing slip carefully.

The module may only be installed and removed by qualified personnel.

4.1.2

General information

The IB IL 24 PSDO 8-PAC safety terminal is designed for use within an Inline station. Only

use the safety terminal in the 24 V DC area of an Inline station.

To ensure reliable operation, install the safety terminal in housing protected from dust and

humidity (IP54 or higher). In order to prevent manipulation, secure the housing (control cab-

inet/control box) against being opened by unauthorized persons.

Mount all Inline terminals on 35 mm DIN rails.

Only connect the cables using the supplied Inline connectors or Inline connectors listed in

the ordering data.

NOTE: Electrostatic discharge

The safety module contains components that can be damaged or destroyed by electro-

static discharge. When handling the safety module, observe the necessary safety precau-

tions against electrostatic discharge (ESD) according to EN 61340-5-1 and EN 61340-5-

WARNING: Unintentional machine startup

Do not mount or remove the module while the power is connected.

Before mounting or removing the module, disconnect the power to the module and the

entire Inline station and ensure that it cannot be switched on again.

Make sure the entire system is reassembled before switching the power back on.

Observe the diagnostics indicators and any diagnostic messages.

The system must only be started when neither the station nor the system can cause any

damage.

Содержание IB IL 24 PSDO 8-PAC

















































































































Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы:

Phoenix Contact IB IL 24 PSDO 8-PAC, Руководство пользователя, Страница: 39 / 112

Результаты поиска

Содержание IB IL 24 PSDO 8-PAC

Отзывы: