Philips QC5135, Руководство пользователя

Страница: 3 / 9

Clipping without beard trimming comb
To trim your facial hair even shorter than 1.5mm (1/16in),
use the appliance without beard trimming comb. This
results in a stubble beard of 1mm (1/32 in).
1 To remove the beard trimming comb, press the
length setting selector (1), move the comb upwards
and then pull it off the appliance (2). (Fig. 14)
2 Place the trimmer on the face and move the
appliance through the hair slowly (Fig. 15).
Cleaning
Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as alcohol,
petrol or acetone to clean the appliance.
Only clean the appliance and the adapter with the
cleaning brush supplied.
Do not use any sharp objects to clean the appliance.
Clean the appliance after every use.
1 Make sure the appliance is switched off and
disconnected from the mains.
2 To remove the comb, press the length setting
selector (1), move the comb upwards and then pull
it off the appliance (2). (Fig. 8)
3 Push the middle part of the cutting unit upwards
with your thumb until it opens (Fig. 16).
4 Clean the cutting unit with the cleaning brush
supplied (Fig. 17).
5 Clean the inside of the appliance with the cleaning
brush supplied (Fig. 18).
6 Clean the hair clipping comb and the beard
trimming comb with the cleaning brush supplied.
Note: The appliance does not need any lubrication.
Replacement
The cutting unit, the adapter and the hair clipping comb
are replaceable.
Replacing the cutting unit
Replace the cutting unit if it is damaged or worn. Only
replace the cutting unit with an original Philips cutting unit.
1 Push the middle part of the cutting unit upwards
with your thumb until it opens and then pull it off
the appliance (Fig. 19).
2 Place the lug of the new cutting unit in the slot
and push the cutting unit onto the appliance
(‘click’) (Fig. 20).
Environment
- Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an official collection point for recycling. By doing
this, you help to preserve the environment (Fig. 21).
- The built-in rechargeable batteries contain substances
that may pollute the environment. Always remove
the batteries before you discard and hand in the
appliance at an official collection point. Dispose
of the batteries at an official collection point for
batteries. If you have trouble removing the batteries,
you can also take the appliance to a Philips service
centre. The staff of this centre will remove the
batteries for you and will dispose of them in an
environmentally safe way (Fig. 22).
Removing the rechargeable batteries
Only remove the rechargeable batteries when you
discard the appliance. Make sure the batteries are
completely empty when you remove them.
Do not connect the appliance to the mains again after
you have removed the rechargeable batteries.
1 Disconnect the appliance from the mains and let
the appliance run until the motor stops.
2 Remove the hair clipping or beard trimming comb
and the cutting unit.
3 Remove the 2 screws at the back of the appliance
with a screwdriver (Fig. 23).
4 Pull the back panel off the appliance (Fig. 24).
5 Remove the 6 screws on the inside of the appliance
with a screwdriver (Fig. 25).
6 Separate the power unit from the front
panel. (Fig. 26)
7 Cut the wires close to the batteries and then
remove the batteries (Fig. 27).
Guarantee and service
If you need service or information or if you have a
problem, please visit the Philips website at
www.philips.
com or contact the Philips Consumer Care Centre
in your country (you find its phone number in the
worldwide guarantee leaflet). If there is no Consumer
Care Centre in your country, go to your local Philips
dealer.
3 4222.002.8144.1