Philips M38 107B4 Скачать руководство пользователя страница 27

Страница: 27 / 82

Electrical Adjustments

Go to cover page

M38 107B4

0. General

8 factory-preset modes

When carry-out the electrical settings in many cases a video signal

must be applied to the monitor. A computer with :

- ATI GPT-1600 (4822 397 10065), Mach 64 (up to 107kHz)

are used as the video signal source. The signal patterns are selected

from the "service test software" package, see user guide 4822 727

21046 (GPT-1600).

0.1 This monitor has

as below.

1. 720 x 400 31.5 kHz/70 Hz 5.

2. 640 x 480 37.5 kHz/75 Hz 6.

4. 800 x 600 53.6 kHz/85 Hz 8.

1. With normal VGA card:

If not using the ATI card during repair or alignment, The service

engineer also can use this service test software adapting with normal

standard VGA adaptor and using standard VGA mode 1024 x768,

68.7 kHz/85 Hz (only) as signal source.

2. AC/DC Measurement:

The measurements for AC waveform and DC figure is based on 1024

x 768 68.7kHz/85 Hz resolution mode with test pattern "gray scale".

Power input: 110V AC

1024x768 60.0 kHz/75 Hz

1024 x 768 68.7 kHz/85 Hz

800 x 600 46.9 kHz/75 Hz

1280 x 1024 80.0kHz/75Hz

640 x 480 43.3 kHz/85 Hz

factory-preload modes as below

640 x 350 37.8 kHz/85 Hz

20. 1024 x 768 48.36 kHz/60 Hz

10. 640 x 480 50.6 kHz/100 Hz 21. 1024 x 768 56.47 kHz/70 Hz

11. 640 x 480 31.6 kHz/60 Hz

22. 1152 x 864 67.5 kHz/75 Hz

12. 640 x 480 37.9 kHz/72.8 Hz 23. 1152 x 864 77.1 kHz/85 Hz

13. 1280 x 960 85.9 kHz/85 Hz 24. 1152 x 870 68.68 kHz/75 Hz

14. 720 x 400 31.469 kHz/70 Hz 25. 1152 x 900 71.8 kHz/76 Hz

15. 720 x 400 37.92 kHz/85Hz

26. 1280 x 1024 63.98 kHz/60 Hz

16. 800 x 600 63.9 kHz/100Hz

27. 1280 x 960 60kHz/60Hz

17. 800 x 600 37.8 kHz/60.3Hz 28. 1600 x 1200 75 kHz/60 Hz

18. 800 x 600 48.07 kHz/72.1Hz 29. 1600 x 1200 81.25 kHz/65Hz

19. 832 x 624 49.7 kHz/74.6Hz

3.Monitor the following auxiliary voltages.

4.5 Adjust brightness controls to center position except for contrast

control which should be set to MAX.

SOURCE ACROSS C2155

-6.1 V +/- 0.2 VDC.

SOURCE ACROSS C2153

+12.2V +/- 1.0 VDC.

SOURCE ACROSS C2154

- 12.2V +/- 1.0 VDC.

SOURCE ACROSS C2151

+93.2V +/- 1.0 VDC.

4.1 During all alignments, supply a distortion free AC mains voltage

to set via an isolating transformer with low internal impedance.

4.2 Align in pre-warmed condition, at least 30 minutes warm-up with

nominal picture brightness.

4.3 Purity, geometry and subsequent alignments should be carried

out in magnetic cage with correct magnetic field.

Northern hemisphere : H=0, V=450 mG, Z=0

Southern hemisphere : H=0, V=-500 mG, Z=0

Equatorial Support

: H=0, V=0

mG, Z=0

4.4 All voltages are to be measured or applied with respect to ground.

SOURCE ACROSS C2152(+ to Gnd) +190.0V +/- 1.0 VDC.

4. General conditions for alignment

Note: Do not use heatsink as ground.

5. To access factory mode

To leave factory mode

5.1 Turn off monitor (don't turn off PC)

5.2 Press "

" and "

" simultaneously on the front control

panel,then press "

",wait till the OSD menu with characters

M 30 107S P V0.82 20010207 (below OSD menu)" come on the

screen of monitor.

5.3 If OSD menu disappears on the screen of monitor, press "

again (anytime), then the OSD menu comes on the screen again.

5.4 Using "

" : to select OSD menu.

5.5 Using "

" : to increase or decrease the setting.

5.6 Using "

" to access/confirm the selection.

5.7 After alignment of factory mode, turn off monitor (if you do not

turn off monitor, the OSD menu is always at the factory mode),

then turn on monitor again (at this moment, the OSD menu goes

back to user mode).

MODEL SELECT

M38

107B4

V0.25

20020701

Factory

Mode

Indicator

6. Picture geometry setting

- Apply a video signal with cross-hatch pattern.

- Apply a video signal in the 1024 x 768 with 68.7 kHz/85 Hz mode.

- Set contrast control at Max. position, and brightness control in the

mid-point.

6.4 Alignment of horizontal geometry and vertical geometry

6.4.1 Adjust the H-width to 306 mm

6.4.2 Adjust the H-phase to center position.

6.4.3 Adjust V-size to 230mm.

6.4.4 Adjust V-Position to center.

Adjust/Trapezoid/pincushion/balance pincushion/paralleogram

6.4.5 Adjust picture tilt via I C BUS for correct top/bottom lines.

6.4.6 Adjust the top and bottom corner by I C to get optimum

corner geometry.

6.4.7 Adjust the parallelogram by I CBUS to get optimum vertical line.

6.4.8 Adjust the balance pincushion by I C BUS to get optimum

vertical line.

6.4.9 Adjust the trapezoid to get optimum vertical line.

6.5 Adjust size/centering/trapezium/pincushion/parallelogram

of all other preset modes via I C bus.

(to repeat from step 6.4.1 to step 6.4.9)

Содержание M38 107B4



















































































Результаты поиска

Содержание M38 107B4

Отзывы:

Похожие инструкции для M38 107B4

Бренды по названию

Популярные бренды

Philips M38 107B4, Руководство по обслуживанию

Результаты поиска

Содержание M38 107B4

Отзывы:

Похожие инструкции для M38 107B4

Бренды по названию

Популярные бренды