Philips M3000A Скачать руководство пользователя страница 182

Страница: 182 / 293

Part 1 Troubleshooting Checklists

166

Troubleshooting the Instrument

Part 1 Troubleshooting Checklists

Checks for Obvious Problems

When first troubleshooting the Instrument, check for obvious problems by answering basic
questions such as the following:

Is the power switch turned on?

Is the battery adequately charged?

If running from mains power supply, is the AC power cord connected to the Instrument
and plugged into an AC outlet?

Are the Measurement Server and, if present, the Measurement Server Extension inserted
correctly?

Checks Before Opening the Instrument

You can isolate many problems by observing indicators on the Instrument before it is
necessary to open the Instrument.

Checks with the Instrument switched Off

• AC connected, without battery:

•

AC Power LED is on (green).

• AC connected, with battery:

•

AC Power LED is on (green).

•

Battery LED is on (green if fully loaded, yellow if being charged).

•

Battery LED red and blinking signals battery malfunction.

• No AC connected, with battery:

•

All LEDs are off.

NOTE

It takes several seconds for the AC Power LED to switch on / off after the mains power cord
has been connected / disconnected.

Содержание M3000A






































































































































































































































































































Результаты поиска

Содержание M3000A

Отзывы:

Похожие инструкции для M3000A

Бренды по названию

Популярные бренды

Philips M3000A, Руководство по обслуживанию

Результаты поиска

Содержание M3000A

Отзывы:

Похожие инструкции для M3000A

Бренды по названию

Популярные бренды