Dry iron
GC180 series
User manual
4215 306 70332
Warranty and service
If you need any information or in case of any problem please contact
your local Philips dealer or authorized service center. For the list of
authorized Philips service centers, please visit the Philips website at
www.philips.com
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit
from the support that Philips offers, register your product at
www.philips.com/welcome
.
General description
1.
Temperature dial
: With this dial you can set the correct temperature for
each kind of fabric, see section setting the temperature.
2.
Temperature light
: The light on the iron acts as an indicator. When this
light goes off the iron is ready for use.
3.
Soleplate
: The base of the iron which comes in contact with the fabric.
4.
Swivel
: It gives freedom of movement and prevents wear and tear of the
cord.
5.
Cord
: It gives easy and free movement to the iron.
6.
Heel
: While not in use and for storage, the iron should be placed on its
heel.
Important
Read this user manual carefully before you use the appliance and save it for
future reference.
Some parts of the iron have been slightly greased and as a result the iron
might slightly smoke when connected for the first time. After a shortwhile,
however, this will cease.
1. Danger:
Never immerse the iron in water.
2. Warning:
• Check if the voltage indicated on the type plate corresponds to the local
mains voltage before you connect the appliance.
• Do not use the appliance if the plug, the cord or the appliance itself shows
visible damage, or if the appliance has been dropped.
• If the mains cord is damaged, you must have it replaced by Philips, a
service centre authorised by Philips or similarly qualified persons in order
to avoid a hazard.
1
2
3
4
5
6
7
• Never leave the appliance unattended when it is connected to the mains.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the
appliance.
• Do not let the mains cord come into contact with the hot soleplate of
the iron.
• When placing the iron on its stand, ensure that the surface on which the
stand is placed is stable.
• The iron is not to be used if it has been dropped, if there are visible signs
of damage.
• WDaE : This appliance is considered to be suitable for use in countries
having a warm damp equable climate. It may also be used in other
countries.
• The appliance is to be supplied through a residual current device (RCD)
having a rated residual operating current not exceeding 30 mA.
3. Caution:
• Only connect the appliance to an earthed wall socket.
• Check the mains cord regularly for possible damage.
• Always place and use the iron on a stable, level and horizontal surface.
• The soleplate of the iron can become extremely hot and may cause burns
if touched.
• When you have finished ironing, when you clean the appliance and also
when you leave the iron even for a short while put the iron on its heel
and remove the mains plug from the wall socket.
• The appliance is intended for household use only.
Quick start guide
• Remove any sticker or packaging material.
• Plug the mains cord in to the power socket.
• Set the temperature using the temperature dial according to the fabric to
be ironed.
• When the temperature light has gone out, the iron is ready for use (fig.1).
Setting the temperature
1. Put the iron on its heel.
2. Set the temperature dial to the required ironing temperature by turning it
to the position of the temperature indicator (fig.2).
• Check the garment label marked on the temprature dial for the required
ironing temperature of respective fabric
- Synthetic fabrics (e.g. acrylic, viscose, poly amide, polyester)
- Silk
- Wool
- Cotton, linen
• When you do not know what kind of fabric(s) the article is made of, try
to iron on a spot which will be invisible when you wear it.
1
2
• Silk, woolen and synthetic materials: iron the reverse side of the fabric to
prevent shiny spots.
• Start ironing the articles that require the lowest ironing temperature, such
as those made of synthetic fibers.
3. Put the mains plug in an earthed wall socket.
Tips
1. Before using the first time remove any sticker or protective foil from the
soleplate. Clean the soleplate with a soft cloth.
2. Keep the sole plate smooth: do not scratch metal object (e.g. rack of
ironing board, buttons, zippers).
3. The ironing results are best if the fabric is slightly damp.
4. Velvet and other textures which rapidly acquire shiny spots should be
ironed in one direction only (with the nap) applying only light pressure.
5. Always keep the iron moving.
6. Iron with a straight back. Adjust the height of the ironing board so that
the handle of the iron is on the same level as your elbow.
7. Pressing onto the iron is not necessary, provided that the temperature has
been set correctly. Ironing is most effective if the laundry is slightly damp.
Cleaning and maintenance
1. Remove the mains plug from the wall socket and let the iron cool down.
2. Wipe the soleplate with a damp cloth and a non-abrasive (liquid) cleaner.
Keep the soleplate smooth: avoid hard contact with metal objects.
3. Clean the upper part of the appliance with a damp cloth.
5. Always store the iron standing on its heel in a safe and dry place.
Trouble shooting
Problem
Possible cause(s)
Solution
The iron is plugged
in but the soleplate is
cold.
Connection problem.
Check the mains cord,
the plug and the wall
socket.
The temperture
control dial is probably
set at minimum
position.
See setting the
temperature section
for appropriate
temperature setting.
Specifications are subject to change without notice
© 2015 Koninklijke Philips N.V.
All rights reserved.
