Philips DVD755VR Скачать руководство пользователя

Страница: 6 / 154

1-5

SERVICE INFORMATION FOR EEPROM IC SETTING

MODEL

NAME

HEX BINARY

DVD755VR/00

OPT1

00000000

OPT2

00000000

OPT3

00000000

OPT4

00000000

OPT5

00000000

OPT6

00000000

DVD755VR/02

OPT1

00000000

OPT2

00000000

OPT3

00000000

OPT4

00000000

OPT5

00000000

OPT6

00000000

DVD755VR/05

OPT1

00000000

OPT2

00000000

OPT3

00000000

OPT4

00000000

OPT5

00000000

OPT6

00000000

DVD755VR/14

OPT1

00000000

OPT2

00000000

OPT3

00000000

OPT4

00000000

OPT5

00000000

OPT6

00000000

WR : OK I : EXIT MOVE :

F G

EDIT :

1. DETECT NEW EEPROM (OPTION EDIT

SCREEN)
- Eeprom EDIT screen automatically appears if

replacing Eeprom.

- Setup option data using the cursor Up/Down key

of a remote control.
(Setup upon BOM depending on OPT1~OPT6
model)

• Since an initial remote control is set to LG for LG

model, appropriately set option data using the
cursor Up/Down key.

• For PHILIPS model, change a remocon key by

using following JIG key.

PHILIPS MODEL : FRONT FF + FRONT REC
KEY(LG/PHILIPS CODE)

2. EEPROM WRITED COMPLETE SCREEN

- Writes data on EEPROM by using REMOCON

"OK".

- If completing the option data screen with a menu

key, Powering Off is automatically done and the
option edit screen is arranged.

3. PG ADJUST

1) Payback the SP standard tape
2) Press the “1” key on the Remote controller and

the “PLAY” key on the Front Panel at the same
time, then it goes into Tracking initial mode.

3) Repeat the above step(No.2), then it finishes

the PG adjusting automatically.

4) Stop the playback, then it goes out to PG

adjusting mode after mony the PG data.

4. EEPROM INITIAL

- SETUP is displayed in the field if pressing the

FRONT REC KEY with the remocon number
"CLEAR" key pressed in the status of no tape.

- AUTO SEARCH is done since the initial screen

of ACMS is serviced if powering On.

- Check basic operation (PLAY/RECORD...)

EEPROM option code No. setting

EEPROM option code No. setting procedure

NAME

HEX

BINARY

OPT1

00000000

OPT2

00000000

OPT3

00000000

OPT4

00000000

OPT5

00000000

OPT6

00000000

WR : OK I : EXIT MOVE :

F G

EDIT :

MASKROM : R00
EEPROM : R00 LG CODE

Содержание DVD755VR



























































































































































Результаты поиска

Содержание DVD755VR

Отзывы:

Похожие инструкции для DVD755VR

Бренды по названию

Популярные бренды

Philips DVD755VR, Руководство по обслуживанию

Результаты поиска

Содержание DVD755VR

Отзывы:

Похожие инструкции для DVD755VR

Бренды по названию

Популярные бренды