Philips DVD755VR Скачать руководство пользователя

Страница: 37 / 154

3-8

3. SERVO CIRCUIT

(1) Unstable Video in PB MODE

Unstable Video in
PB Mode.

Does the Noise level of the
screen change
periodically?

Do the CTL pulses appear
at the IC501 Pin8?

Is adjusting the height of
the CTL Head accurate?

Readjust the height of the
CTL Head.

Replace the IC501.

Refer to “When the Y signal
doesn’t appear on the
screen in PB Mode”.

Does the CFG waveform
appear at the IC501
Pin9?

On tracking do the CTL
pulses move?

Does the Video Envelope
waveform appear at the
IC501 Pin24?

Replace the IC501.

YES

(2) When the Drum Motor

(2)

doesn’t run.

Do the DFG Pulses appear
at the PMC01 Pin11?

Replace the Cap M.

Aren’t the foil patterns and

the Components between
IC501 Pin104 and PMC01
Pin11 short?

Replace the IC501.

Refer to “(2)
No 12VA of Power section”

Do the Drum PWM Pulses
appear at the IC501
Pin107?

Aren’t the foil patterns and

the Components between
IC501 Pin107 and PMC01
Pin12 short?

Do the DFG Pulses appear

at the IC501 Pin104?

Do the Drum PWM Pulses
appear at the IC501
Pin107?

Aren’t the connecting patterns and the Components

between IC501 Pin107 and PMC01 Pin12 short?

When the Drum Motor
doesn’t run,

Does 12V appear at the
PMC01 Pin8?

Does 2.8V appear at the
PMC01 Pin12?

Check the connector
(PMC01) and the Drum
Motor Ass’y.

YES

Содержание DVD755VR



























































































































































Результаты поиска

Содержание DVD755VR

Отзывы:

Похожие инструкции для DVD755VR

Бренды по названию

Популярные бренды

Philips DVD755VR, Руководство по обслуживанию

Результаты поиска

Содержание DVD755VR

Отзывы:

Похожие инструкции для DVD755VR

Бренды по названию

Популярные бренды