background image

Diamond Line Amplifiers

10 July 2000

37

D

ia

m

o

n

d

 

The main output test point 
allows access to the return 
band as well. You can’t 
measure return signal here, 
but you can inject return test 
signals.

Main Output Test Point. 

The main output test point is a 

-20 dB directional coupler, which isolates the measured 
forward signal from the effects of reflections in the cable. 
Accessible through a cut-out in the module cover, this test 
point lets you verify the forward signals at the main output 
port (J2) without interrupting the amplifier’s operation.

Main Output Port (J2). 

The main output port, J2, routes 

forward outgoing signal to a distribution cable. (This port also 
routes incoming return signal to the amplifier.)

Secondary Path (after it splits from main path)

Secondary Output Attenuator. 

A 9-A-WC or 10-A-WC series 

attenuator reduces signal levels at the secondary output port 
(J3 or J4). A “zero” attenuator is shipped in this slot for circuit 
continuity.

Secondary Output Post-Amplifier. 

The RF from this hybrid, 

which uses Power Doubling technology, goes to the 
secondary output port(s).

Secondary Output Port Selector. 

Accessible through a cut-out 

in the module cover, the output port selector directs signal to 
the secondary output port(s): J3 only, J4 only, or both J3 and 
J4. A jumper, or “zero” attenuator, is used when directing 
signal to only one port

.

 When using both ports, this location 

accepts a DC4-WC, DC8-WC, or DC12-WC directional 
coupler plug-in.

Secondary Output Diplex Filter. 

See “Input Diplex Filter” on 

page 35.

A secondary output test point 
allows access to the return 
band as well. You can’t 
measure return signal here, 
but you can inject return test 
signals.

Secondary Output Test Point. 

A secondary output test point is 

a -20 dB directional coupler, which isolates the measured 
forward signal from the effects of reflections in the cable. 
Accessible through a cut-out in the module cover, this test 
point lets you verify the forward signals at the secondary 
output port (J3 or J4) without interrupting the amplifier’s 
operation.

Secondary Output Port (J3 or J4). 

A secondary output port 

routes forward outgoing signal to a distribution cable. (This 
port also routes incoming return signal to the amplifier.)

Содержание Diamond Line 2

















Отзывы: