channels and radio stations.
Remove a Satellite
You can remove one or more satellites from your
current satellite installation. You remove the satellite
and its channels. Some satellite operators do not
allow removing a satellite.
To remove satellites…
1 -
Select
Settings
>
Channels
>
Satellite
Installation
and press
OK
.
2 -
Select
Search for satellite
and press
OK
.
3 -
Select
Remove Satellite
and press
OK
. The
current satellites are shown.
4 -
Select a satellite and press
OK
to mark or
unmark them to remove.
5 -
Press
(left) repeatedly if necessary, to close
the menu.
Manual Installation
Manual Installation is intended for expert users.
You can use Manual Installation to quickly add new
channels from a satellite transponder. You need to
know the frequency and polarization of the
transponder. The TV will install all channels of that
transponder. If the transponder was installed before,
all its channels - the former and the new ones - are
moved to the end of the channel list All.
You cannot use Manual installation if you need to
change the number of satellites. If this is needed, you
have to do a complete installation with Install
Satellites.
To install a transponder…
1 -
Select
Settings
>
Channels
>
Satellite
Installation
and press
OK
.
2 -
Select
Manual Installation
and press
(right)
to enter the menu.
3 -
If you have more than 1 satellite installed,
select
LNB
for which you want to add channels.
4 -
Set the
Polarisation
you need. If you set
the
Symbol Rate Mode
to
Manual
, you can enter
the symbol rate in
Symbol Rate
manually.
5 -
Press the arrows
(up) or
(down) to adjust
the frequency, and select
Done
.
6 -
Select
Search
and press
OK
. The signal
strenght is shown on screen.
7 -
If you want to store the channels of a new
transponder, select
Store
and press
OK
.
8 -
Press
(left) repeatedly if necessary, to close
the menu.
Homing Transponder and LNB
In some countries, you can adjust the expert settings
for homing transponder and each LNB. Only use or
change these settings when a normal installation fails.
If you have non-standard satellite equipment, you
can use these settings to overrule the standard
settings. Some providers might give you some
transponder or LNB valeus which you can enter here.
LNB Power
By default, LNB Power is set to Automatic.
22 kHz Tone
By default, the Tone is set to Automatic.
Low LO Frequency / High LO Frequency
The local oscillator frequencies are set to standard
values. Adjust the values only in case of exceptional
equipment that needs different values.
Problems
The TV cannot find the satellites I want or the TV
installs the same satellite twice
• Make sure that the correct number of satellites is set
in Settings at the start of the installation. You can set
the TV to search for One, Two or 3/4 satellites.
A dual head LNB cannot find a second satellite
• If the TV finds one satellite but cannot find a second
one, turn the dish a few degrees. Align the dish to get
the strongest signal on the first satellite. Check the
signal strength indicator of the first satellite on screen.
With the first satellite set at the strongest signal, select
Search again to find the second satellite.
• Make sure the settings are set to Two Satellites.
Changing the installation settings did not solve my
problem
• All settings, satellites and channels are only stored
at the end of the installation when you finish.
All satellite channels are gone
• If you use a Unicable system, make sure you
assigned two unique user band numbers for both
built-in tuners in the Unicable settings. It might be
that another satellite receiver in your Unicable system
is using the same user band number.
Some satellite channels seem to have disappeared
from the channel list
• If some channels seem to be gone or displaced, the
broadcaster might have changed the transponder
location of these channels. To restore the channel
positions in the channel list, you can try an update of
23
Содержание 55OLED854
Страница 95: ...Powered by TCPDF www tcpdf org 95 ...
