Philips 50 T Series Скачать руководство пользователя страница 45

Страница: 45 / 105

Using the Service Program

Chapter 6 - Using the Service Software

Using the Service Program

When the program has been loaded onto your PC, the main menu is
displayed. (If the menu is not displayed an error message is displayed along
the bottom of the screen).

Main Menu

--------------------------------------------------------------------------------------

--M1310A Service Software Rev.A.xx.xx--

MAIN MENU

_ Program S/N to Transmitter

_ Program S/N to Receiver

_ Power On Selftest

_ Show last errors/warnings

_ Check Transmitter

_ Check Receiver

_ Read SerNum and Revisions

_ Reset Serial Number

_ Read country information

_ EXIT

--------------------------------------------------------------------------------------

Select with >cursor keys < up >, < down >,< enter >

--------------------------------------------------------------------------------------

Содержание 50 T Series










































































































Результаты поиска

Содержание 50 T Series

Отзывы:

Philips 50 T Series, Руководство по обслуживанию, Страница: 45 / 105

Результаты поиска

Содержание 50 T Series

Отзывы: