17” CDT Color Monitor 107S7
15
(4). Choose 1 for LH,set R or G or B gain, make x=283±15, y=297±15
,
Y=140±15
cd/m
2
,then save it into
9300K color temperature, set R or G or B gain, make x=313±15, y=329±15,Y=130
±
15,then save it into 6500K
color temperature.
F. White screen appears, brightness cut off, set “SB” as 4,adjust AB value, make 9300K color temperature
Y=98
±
1 cd/m
2
,then save it into 9300K color temperature; set “SB” as 3,adjust AB value,
make 9300K color
temperature Y=96
±
1 cd/m
2
,then save it into 9300K color temperature; set “SB” as 2, make 9300K color
temperature Y=94
±
1 cd/m
2
,then save it into 9300K color temperature; set “SB” as 1, make 9300K color
temperature Y=92
±
1 cd/m
2
,then save it into 9300K color temperature.
G. After modulation, it’s necessary to check if the white balance accords with the normal specification. If not,
needs reset. then exit factory setting area.
4.Focus Adjustment:
A. Set mode7 1024×768@85Hz with character full page.
B.Under the RECALL state.
C.Then adjust focus VR1 to a fine vertical line.
D.Adjust focus VR2 to a fine horizontal line.
E. Repeat step C & D,after that ,set the Focus VR,G2 VR with the white lacquer.
5. Purity Adjustment
A. Be sure that the display is not being exposed to any external magnetic fields.
B.Ensure that the spacing between the Purity, Convergence, Magnet, (PCM), assembly and the CRT stem is
29mm. (See below diagram)
C.Produce a complete, red pattern on the display. Adjust the purity magnet rings on the PCM assembly to
obtain a complete field of the color red. This is done by moving the two tabs in such a manner that they
advance in an opposite direction but at the same time to obtain the same angle between the two tabs, which
should be approximately 180'.
D.Check the complete blue and complete green patterns to observe their respective color purity. Make minor
adjustments if needed.
Relative placement of typical components
Purity Magnets
Deflection Yoke
4-pole Convergence Magnets
6-pole Convergence Magnets
6. Convergence adjustment
A. Produce a magenta crosshatch on the display.
B. Adjust the focus for the best overall focus on the display.
Also adjust the brightness to the desired condition.
C. Vertical red and blue lines are converged by varying the angle between the two tabs of the 4 pole magnets
on the PCM assembly. (See above diagrams)
D. Horizontal red and blue lines are converged by varying the two tabs together, keeping the angle between
them constant.
E. Produce a white crosshatch pattern on the display.
F. Vertical green and magenta lines are converged by varying the angle between the two tabs of the 6-pole
magnets.
G. Horizontal green and magenta lines are converged by varying the two tabs together, keeping the angle
between them constant.
Содержание 107S7
