Philips 107B50/74 Скачать руководство пользователя страница 39

Страница: 39 / 75

0. Warning

1. Servicing of SMDs (Surface Mounted Devices)

All ICs and many other semi-conductors are susceptible to

electrostatic discharges (ESD). Careless handling during

repair can reduce life drastically. When repairing, make sure

that you are connected with the same potential as the mass

of the unit via a wrist wrap with resistance. Keep components

and tools also at the same potential !

- Oxidation on the terminals of SMDs results in poor soldering.

Do not handle SMDs with bare hands.

- Avoid using storage places that are sensitive to oxidation

such as places with sulphur or chlorine gas, direct sunlight,

high temperatures or a high degree of humidity. The

capacitance or resistance value of the SMDs may be

affected by this.

- Rough handling of circuit boards containing SMDs may

cause damage to the components as well as the circuit

boards. Circuit boards containing SMDs should never be

bent or flexed. Different circuit board materials expand and

contract at different rates when heated or cooled and the

components and/or solder connections may be damaged

due to the stress. Never rub or scrape chip components as

this may cause the value of the component to change.

Similarly, do not slide the circuit board across any surface.

- Heat the solder (for 2-3 seconds) at each terminal of the

chip. By means of litz wire and a slight horizontal force,

small components can be removed with the soldering iron.

They can also be removed with a solder sucker (see Fig.

1A)

- While holding the SMD with a pair of tweezers, take it off

gently using the soldering iron's heat applied to each

terminal (see Fig. 1 B).

- Remove the excess solder on the solder lands by means of

litz wire or a solder sucker (see Fig. 1C).

- When handling the soldering.iron. use suitable pressure and

be careful.

- When removing the chip, do not use undue force with the

pair of tweezers.

- The soldering iron to be used (approx. 30 W) should

1.1 General cautions on handling and storage

1.2 Removal of SMDs

1.3 Caution on removal

preferably be equipped with a thermal control (soldering

temperature: 225 to 250 C).

- The chip, once removed, must never be reused.

1.4 Attachment of SMDs

- Locate the SMD on the solder lands by means of tweezers

and solder the component on one side. Ensure that the

component is positioned correctly on the solder lands (see

Fig.2A).

- Next complete the soldering of the terminals of the

component (see Fiq. 2B).

- When soldering the SMD terminals, do not touch them

directly with the soldering iron. The soldering should be

done as quickly as possible, care must be taken to avoid

damage to the terminals of the SMDs themselves.

- Keep the SMD's body in contact with the printed board when

soldering.

- The soldering iron to be used (approx. 30 W ) should

preferably be equipped with a thermal control (soldering

temperature: 225 to 250 C).

- Soldering should not be done outside the solder land.

- Soldering flux (of rosin) may be used, but should not be

acidic.

- After soldering, let the SMD cool down gradually at room

temperature.

- The quantity of solder must be proportional to the size of the

solder land. If the quantity is too great, the SMD might

crack or the solder lands might be torn loose from the

printed board (see Fig. 3).

2. Caution when attaching SMDs

SOLDERING

IRON

RIGHT

Fig. 3 Examples

DISMOUNTING

VACUUM PISTON

4822 395 10159

SOLDERING

IRON

e.g. WELLER

SOLDER TIP PT -H7

SOLDERING

IRON

SOLDER WICK

4822 321 40042

SOLDERING

IRON

SOLDER WICK

e.g. A PAIR OF TWEEZERS

HEATING

Fig. 1

e.g. A PAIR OF TWEEZERS

SOLDER

0.5 - 0.8 mm

SOLDER

0.5 - 0.8 mm

SOLDERING

IRON

SOLDERING TIME

< 3 sec/side

SOLDERING

IRON

PRESURE

MOUNTING

Fig. 2

Repair Tips

Go to cover page

V30 107B5

http://jdwxzlw.5d6d.com/?fromuser=华盛维修

家电维修资料网，免费下载各种维修资料

Содержание 107B50/74












































































Результаты поиска

Содержание 107B50/74

Отзывы:

Похожие инструкции для 107B50/74

Бренды по названию

Популярные бренды

Philips 107B50/74, Руководство по обслуживанию

Результаты поиска

Содержание 107B50/74

Отзывы:

Похожие инструкции для 107B50/74

Бренды по названию

Популярные бренды