PHICOMM FD-221 Скачать руководство пользователя | Manualshive

Страница: 57 / 61

background image

52

Appendix B: Certification

ADSL2/2+ Modem Router

www.phicomm.com

Appendix B: Certification

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

•

Consult the dealer or an experienced radio/ TV technician for help.

•

FCC Caution

•

Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.

«
...
55
56
57
58
59
...
»

Содержание FD-221






























































Отзывы:

Нет отзывов

Похожие инструкции для FD-221

Бренд: Wattle Страницы: 6

Бренд: Baicells Страницы: 8

Бренд: IBM Страницы: 4

Бренд: Conceptronic Страницы: 230

Бренд: ZyXEL Communications Страницы: 2

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Бренд: ZyXEL Communications Страницы: 282

Бренд: TP-Link Страницы: 2

Enterasys Matrix 2G4082-25

Бренд: Enterasys Страницы: 58

FieldPoint FP-3000

Бренд: National Instruments Страницы: 118

Elinx EIR510 Series

Бренд: B&B Electronics Страницы: 2

Бренд: Casablanca Страницы: 13

Бренд: LUX LUMEN Страницы: 41

Wisenet XRN-6410RB2-24TB

Бренд: Hanwha Techwin Страницы: 124

Бренд: ADTRAN Страницы: 4

Бренд: Pro-Nets Technology Corporation Страницы: 48

Cascade Express

Бренд: Riverbed Страницы: 92

Бренд: netsys Страницы: 38

Бренд: Billion Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды