Phason AutoFlex Connect Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 54

Phason AutoFlex Connect Скачать руководство пользователя страница 22

Connecting equipment to modules

22

Connecting equipment to Variable DC Modules

The Variable DC Module (model

VDC-4

) has four 0 to 10 V outputs for controlling variable

frequency drives or FanDRIVEs.

The ratings of the equipment you connect must not

exceed the ratings of the Variable DC Module.



0 to 10 VDC, 2K Ω load

FanDRIVEs

FanDRIVEs are for controlling AC variable fans, and are a cost-effective way to increase the
capacity of your fan control system. Installation is simple and there is no additional configuration
required; FanDRIVEs follow the programming of the AutoFlex.

There are two FanDRIVE models available. Model FD-2-7 has two 7 FLA stages, model FD-1-14
has one 14 FLA stage. For more information about FanDRIVEs, visit

www.phason.ca

.

To connect variable frequency drives or FanDRIVEs

The disconnect relay for the variable frequency drive is a relay on an RM-4 module.

Configure the relay to follow the variable DC output. For more information, refer to

the online help at the AutoFlex Connect display.

«
...
20
21
22
23
24
...
»

Содержание AutoFlex Connect























































Отзывы:

Нет отзывов