Petsafe In-Ground Fence ZIG00-14654 Скачать руководство пользователя

Страница: 6 / 32

+1 (800) 732-2677

How the System Works

A radio signal travels from the Fence Transmitter through a buried wire, marking the boundaries you wish to set for your

dog. Your dog wears a Receiver Collar that detects the signal at the boundary. As your dog approaches the boundary, the

receiver issues a warning tone. If he proceeds further, he receives a safe but startling Static Correction. While harmless, the

correction will persuade him to stay in the containment area you’ve established. Boundary flags are a temporary visual aid

for your pet; remove them after training. This PetSafe

In-Ground Fence

™

system has been proven safe, comfortable, and

effective for pets over 8 pounds.

Key Definitions

Fence Transmitter:

Transmits the radio signal through the Boundary Wire.

Pet Area:

Area within the Warning Zone where your pet can roam freely.

Warning Zone:

Outer edge of the Pet Area where your pet’s Receiver Collar begins to

beep, warning him not to go into the Static Correction Zone.

Static Correction Zone:

Zone beyond the Warning Zone where your pet’s Receiver

Collar will emit a Static Correction, signaling him to return to the Pet Area.

Boundary Width:

Combination of the Warning Zone and the Static Correction Zone.

Surge Protector:

Installed with the Fence Transmitter to protect it from lightning strikes

and power surges (USA and Canada only).

Receiver Collar:

Receives the radio signal from the Boundary Wire.

Correction Level Button:

Adjusts the level of Static Correction your pet receives

in the Static Correction Zone.

Receiver Indicator Light:

Indicates the level of correction at which the Receiver Collar

is set. This light also serves as a low battery indicator.

Contact Points:

Delivers the safe Static Correction when your pet moves into

the Static Correction Zone.

Power Jack:

Where the Power Adapter plugs into the Fence Transmitter.

Boundary Control Switch:

Switch located on the

Fence Transmitter to adjust according to the length of

Boundary Wire used.

Boundary Wire Terminals:

Where the Boundary

Wires connect to the Fence Transmitter in order to

complete a continuous loop.

Loop Indicator Light:

Indicates that the Boundary

Wire makes a complete loop, enabling the signal to be

transmitted.

Boundary Width Control:

Adjusts the width of

the Warning and Static Correction Zones.

Note:

Adjusting the knob does not change the level of Static

Correction on the Receiver Collar.

Correction Level Button

Battery

Contact Points

Receiver

LED

Indicator Light

Washers

Receiver Collar

Boundary Control Switch

Boundary Wire

Terminals

Loop Indicator Light

Power Light

Power

Jack

Boundary Width

Control

Fence Transmitter

Fence

Transmitter

Static

Correction

Zone

Warning

Zone

Static

Correction

Zone

Warning

Zone

Pet

Area

Boundary

Width

Surge

Protector

with Power

Adapter

Содержание In-Ground Fence ZIG00-14654

































Результаты поиска

Содержание In-Ground Fence ZIG00-14654

Отзывы:

Похожие инструкции для In-Ground Fence ZIG00-14654

Бренды по названию

Популярные бренды

Petsafe In-Ground Fence ZIG00-14654, Руководство по эксплуатации продукта

Результаты поиска

Содержание In-Ground Fence ZIG00-14654

Отзывы:

Похожие инструкции для In-Ground Fence ZIG00-14654

Бренды по названию

Популярные бренды