Peterbilt 325 2017 Скачать руководство пользователя страница 259

Страница: 259 / 392

LUBRICANT SPECIFICATIONS

Meritor Axle Lubrication

NOTE

Axles utilized in 100% off-highway
use are not eligible for Meritor’s Ad-
vanced Lube Rear Drive Axle pro-
gram.

Under Meritor’s Advanced Lube Rear
Drive Axle program, the axles listed
below are exempt from an initial
lubricant change:

AVAILABLE ADVANCED LUBE AXLES

RS-17-145

RS-23-180

RT-40-145

RT-44-145P

RS-19-145

RS-26-180

RT-40-145P

RT-46-160

RS-21-145

RS-30-180

SQ-100A

RT-46-160P

RS-23-160

RT-34-145

SQ-100AP

RT-52-160

RS-23-161

RT-34-145P

RT-44-145

RT-52-160P

Meritor rear axles that do not appear
on the list above will continue to
require an initial drain at 3000-5000
miles (4800-8000 km).

•

Refer to the Meritor Field
Maintenance Manual for a
particular axle for lubricant
specifications.

•

See your dealer for
Meritor-approved lubricant
brands.

•

Refer to the following chart for
lubricant change intervals:

(03/17)

Y53-6060-1C1

5-49

Содержание 325 2017









































































































































































































































































































































































































Результаты поиска

Содержание 325 2017

Отзывы:

Бренды по названию

Популярные бренды

Peterbilt 325 2017, Руководство оператора

Результаты поиска

Содержание 325 2017

Отзывы:

Бренды по названию

Популярные бренды