Peterbilt 325 2017 Скачать руководство пользователя | Manualshive

Страница: 184 / 392

background image

CRUISE CONTROL

CRUISE CONTROL

Cruise Control Switch

This vehicle may have cruise control
switches located on the steering wheel
instead of the switches on the dash
board. The instructions are still the
same.

•

To Turn On:

Press the ON/OFF button.

•

To Turn Off:

Press the ON/OFF button. Any
previous speed settings are cleared.

Using Cruise Control While Driving

Setting Cruise Speed

1.

Ensure that the vehicle speed is
above the minimum cruise control
speed (19 mph (30 km/h) for
PACCAR MX engine and 30 mph

(48 km/h) for the Cummins and
PACCAR PX series engines) and
the engine speed is above 1100
rpm.

2.

Press the "ON/OFF" button.

3.

Accelerate the vehicle to the
desired cruise speed.

4.

Press the "SET" button to set the
cruise speed.

NOTE

Cruise Control may not hold the set
speed going down hills. If the speed
increases going down a hill, use the
brakes to slow down. This will can-
cel Cruise Control.

Changing the Cruise Set Speed

For vehicles with cruise control buttons
on the steering wheel, the cruise
speed may be changed by using the
+/- button. The pressing and holding
the + button will increase speed while
pressing and holding the - button will
decrease speed. For vehicles with
dash mounted cruise control switches,
changing the speed is done through
the "Set/Resume" button. To increase
the speed, press and hold the Set
button. To decrease the speed, press
and hold the "Resume" button.

Cancelling Cruise Control

You can cancel cruise control in any
of these ways:

•

Tap the brake pedal.

•

Tap the clutch pedal.

4-44

Y53-6060-1C1

(03/17)

4

«
...
182
183
184
185
186
...
»

Содержание 325 2017









































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 325 2017

ALLEY-GATOR RIGHT-HAND

Бренд: Labrie Страницы: 73

Бренд: DAF Страницы: 58

swaploader SL-105

Бренд: Efco Страницы: 82

Бренд: UD Trucks Страницы: 385

Бренд: Warren Страницы: 41

Бренд: U-Line Страницы: 6

Бренд: Denios Страницы: 20

Бренд: LGMG Страницы: 165

Бренд: Movexx Страницы: 61

Ergomover 620 AC-TT

Бренд: BT Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды