Peterbilt 325 2017 Скачать руководство пользователя страница 133

Страница: 133 / 392

HEATING AND AIR CONDITIONING

Turn the Air Flow Control Dial
to Dash Vents.

If the outside air is not cold
enough to cool the cab, press to
engage the compressor which
will deliver colder air.

For more cooling effect, you
may need to press the switch
back to recirculation mode.

To Heat

Turn the Fan Control Dial ON to
the desired fan speed.

Turn the Air Flow Control Dial
to Floor Vents.

Adjust the Temperature Control Dial
clockwise until the air temperature
feels comfortable.

Using this function in "manual" mode
will provide the maximum heating
performance.

To Dehumidify

Push the Fresh Air/Recirculate
Switch to the Fresh Air mode
(Blue indicator light off).

Turn ON the Air Conditioning
Switch (Blue indicator light on).

Turn ON the Fan Control Dial to
the desired fan speed.

Adjust the Temperature Control
Dial until the air temperature feels
comfortable.

The air conditioner removes moisture
from the air while the heater heats the
air.

To Defog and Defrost the Windshield

Turn the Fan Control Dial
clockwise to the highest fan
speed.

Turn the Air Flow Control Dial to
Defrost Vents.

(03/17)

Y53-6060-1C1

3-67

Содержание 325 2017









































































































































































































































































































































































































Результаты поиска

Содержание 325 2017

Отзывы:

Бренды по названию

Популярные бренды

Peterbilt 325 2017, Руководство оператора

Результаты поиска

Содержание 325 2017

Отзывы:

Бренды по названию

Популярные бренды