Peter electronic VersiStart p III 105 Скачать руководство пользователя страница 88

Страница: 88 / 108

VersiStart p III

NOTE

DHCP addressing is available with Modbus TCP and Ethernet/IP. DHCP
addressing is not supported with Profinet.

11U – Location ID

Range:

0 - 65535

Default:

Description:

Sets the soft starter's unique location ID.

10.16 12 Pump Input Configuration

NOTE

The parameters in this group are only active if a smart card is installed.

12A – Auto-Reset Count

Range:

0 – 5

Default:

Description:

Sets how many times the soft starter will auto-reset, if it continues to
trip.

The reset counter increases by one each time the soft starter auto-
resets, and resets after a successful start.

Setting 12A to zero disables auto-reset.

NOTE

Auto-reset will reset trips from any source, not just from the smart card.

12B – Auto-Reset Delay

Range:

0:05 - 15:00 (minutes:seconds)

Default:

5 seconds

Description:

Sets a delay before the VersiStart p III will auto-reset a trip.

12C – Pressure Sensor Type

Options:

None (default)
Switch
Analog

Description:

Selects which type of sensor is associated with the pressure sensor
input on the smart card.

12D – Pressure Units

Options:

Bar
kPa (default)
Psi

Description:

Selects which units the sensor will use to report the measured
pressure.

12E – Pressure at 4 mA

Range:

0 – 5000

Default:

Description:

Calibrates the soft starter to the 4 mA (0%) level of the pressure
sensor input.

Содержание VersiStart p III 105













































































































Результаты поиска

Содержание VersiStart p III 105

Отзывы:

Бренды по названию

Популярные бренды

Peter electronic VersiStart p III 105, Инструкции по сборке и пусконаладке

Результаты поиска

Содержание VersiStart p III 105

Отзывы:

Бренды по названию

Популярные бренды