background image

VBMS .... 

5

5.

EC Declaration of Conformity

 

EC Declaration of Conformity  

 
 
 
 

The manufacturer / company placing the product on the market

 

(authorized representatives of the manufacturer / companies placing the product on the market
that are established within the Community) 

 

 

 
 
Name / Address:  

 

 

PETER electronic  GmbH & Co. KG

 

 

 

 

 

 

Bruckäcker 9 

 

 

 

 

 

92348 Berg 

 
hereby declares that the following product (device, component, unit) in the version as supplied

 

 

 

 

 

Product designation:  

 

Combined Motor Start and Braking Device

 

Series / type designation:

  

VBMS 230-1,5/20; VBMS 400-2,2/20

 

Article number: 

 

 

2C0...

 

Year of manufacture: 

 

 

 

 

2007

 

 

 

 

 

 

 

  

 

 
 

complies with the provisions of the following EU-directives:

 

 
 

2014/30/EU

2014/35/EU

2011/65/EU

 

 

 

 

 

 

 

 
 
 

 
 
 
 

 

This EC Declaration of Conformity is no longer valid, if the product is modified or changed 
without our agreement.
This declaration is issued under the sole responsibility of the signatory.

 

 
 
 
 
 
 

Berg, 15.04.2016     Dr. Thomas Stiller, Managing director                           

(place, date) 

 

(signatory and function of the signatory)

 

 

(signature)  

Electromagnetic compatibility

Electrical equipment designed for use within certain voltage limits

The restriction of the use of certain hazardous substances in 
electrical and electronic equipment

The following harmonized standards have been applied:

EN 60947-1:2007+A1:2012

EN 60947-4-2:2012

Low-voltage switchgear and controlgear General rules

Low-voltage switchgear and controlgear
Contactors and motor-starters - AC semiconductor motor
controllers and starters

Содержание 2C000.23020























Отзывы: