background image

 

 

ROOF RACK INSTALLATION INSTRUCTIONS 

(35”, 45, & 55” RAIL LENGTHS) 

 

 

 

1549 US Highway 21 South 

Sparta, NC  28675 

336-372-2545 

[email protected]

 

www.perrycraft.com

 

 

ROOF RACK INSTALLATION INSTRUCTIONS

 

(35”, 45” and 55” RAIL LENGTHS) 

Before contacting/returning this product to your place of 
purchase, contact 

Perrycraft, Inc.

® at 336-372-2545 for any 

technical questions, problems, missing parts, etc., upon opening your 
product and verifying all parts are present. 

RETURNS:  

Any product to be returned must be returned to the place 

of purchase, and is subject to the seller’s returns policy.  

DO NOT

 

return to Perrycraft unless instructed to do so in writing. 

IMPORTANT NOTES: 

RACK LOCATION:

  Perrycraft’s products are manufactured to be 

installed into the skin of the roof panel of vehicles.  They are not 
designed to line up or be installed at the factory fitment points 
available on some vehicles. 

INSTALLATION HARDWARE:

  The included hardware pack contains 

screws for securing this rack to a sheet metal roof or metal surface.  
To install this rack on fiberglass or composite camper tops, tonneau 
covers, or Jeep

©

 tops, please contact your seller to purchase 

hardware pack HWDSTC-UV, or call 336-372-2545 to purchase 
directly from 

Perrycraft, Inc.

® 

SIDE RAIL CURVATURE:

  

Perrycraft, Inc.

® manufactures racks and rails 

that are size specific, not vehicle specific.  Therefore, the bow of the 
rails (front to back) may need adjusting.  Place the rails (without the 
stanchions) on the roof in the desired location.  Ideally, the rails 
should match the roof curvature.  The ends of the rails should touch 
the roof and the center should be no more than 3/16” off the roof 
surface.  The rails can be adjusted (more bow or less bow) by placing 
the ends of the rails on supports and either pressing down from the 
top (to take away bow), or pressing down from the bottom (to add 
more bow).  Rails are heat

 

treated aluminum, therefore, very strong.  

Several attempts of adjustment may be required to get the correct 
curvature.

 

 

2

 

Содержание DynaSport Roof Rack

Страница 1: ...INSTALLATION HARDWARE The included hardware pack contains screws for securing this rack to a sheet metal roof or metal surface To install this rack on fiberglass or composite camper tops tonneau covers or Jeep tops please contact your seller to purchase hardware pack HWDSTC UV or call 336 372 2545 to purchase directly from Perrycraft Inc SIDE RAIL CURVATURE Perrycraft Inc manufactures racks and ra...

Страница 2: ... side of cross bar Secure connectors to cross bars with 8 x 1 2 screws through pre drilled holes underneath 2 Slide cross bar assemblies into top side of rails Tighten thumbscrews enough to keep cross bars from sliding but loose enough for rail to pivot Crossbars should be placed approximately 7 inches from the ends of the rails so that the installation will be as square as possible 3 Insert rails...

Страница 3: ...increases the load weight to the cross bars and roof Large or flat items such as plywood ladders lumber hang gliders canoes kayaks etc can trap air and create wind lift Secure the ends of long objects directly to the front and back bumpers or tie down positions 5 Bulky or tall loads can create tremendous horizontal wind resistance from headwinds and crosswinds Extreme caution should be used when t...

Страница 4: ... no warranty and accepts no liability for normal wear and tear incorrect installation damage to vehicles property and or equipment nor damage arising from improper use The sole remedy under this warranty agreement is replacement of component parts during the warranty period You may be required to send in the component in question at your expense to have the part evaluated for a warranty claim If y...

Отзывы: