PermaGreen Supreme MAGNUM SmartSteer C3C 2009 страница 70 Скачать руководство пользователя

Страница: 70 / 73

Magnum C3C Spreader Sprayer

Operator Manual

Refer to the cover page for restrictions regarding

Page 70

reproduction or disclosure of this material.

Septenber/08

MAINTENANCE (continued)

SCHEDULED QUARTERLY OR EVERY 300 HOUR MAINTENANCE AND SAFETY

CHECKLIST LOG

Ride-On Magnum C3C Serial No.__________

Reproduce sheets for this machine and record maintenance. Keep with machine.

QUARTERLY MAINTENANCE or EVERY 300 HOURS OF OPERATION

DATE

INITIALS

HOUR

METER

READING

CHECK

OFF

MAINTENANCE TO BE PERFORMED

Perform Daily maintenance

Change engine oil.

Change engine gearbox oil.

Replace the air filter (refer to the engine manual).

Clean the sediment cup (refer to the engine
manual).

Check and adjust the spark plug (refer to the
engine manual).

Check the fuel tank for contamination and residue.
Clean the tank and filter if necessary.

Calibrate spreader system. Operator Manual page
301

Calibrate sprayer system. Operator Manual page
305

Check cables. Replace if worn or damaged.

Check and adjust the valve clearance*.

Grease rear wheel bearings.

Grease the articulating rod ends.

Grease the pillow blocks.

Grease (2) transaxle zerks on front, underside

Grease (2) Front wheel hubs

Check the belts. Replace if necessary.

Check and adjust the brakes.

Check the spinner platter. Replace if necessary.

NOTES:

Perform Safety Systems Check (Section 3)

*Unless you are technically qualified, these checks and adjustments must be done by an
authorized Honda service center.

Содержание MAGNUM SmartSteer C3C 2009










































































Результаты поиска

Содержание MAGNUM SmartSteer C3C 2009

Отзывы:

Похожие инструкции для MAGNUM SmartSteer C3C 2009

Бренды по названию

Популярные бренды

PermaGreen Supreme MAGNUM SmartSteer C3C 2009, Руководство оператора

Результаты поиска

Содержание MAGNUM SmartSteer C3C 2009

Отзывы:

Похожие инструкции для MAGNUM SmartSteer C3C 2009

Бренды по названию

Популярные бренды