Perkins 854E-E34TA Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 252

Perkins 854E-E34TA Скачать руководство пользователя страница 70

(Table 28, contd)

Troubleshooting Test Steps

Values

Results

7. Electronic Unit Injectors

A. Use the electronic service tool to check for active diagnostic co-
des that relate to the electronic unit injectors.

Diagnostic
codes

Result:

There are active diagnostic codes relating to the

fuel injectors.

Troubleshoot any active diagnostic codes associated with
the fuel injectors. Refer to Troubleshooting, “Diagnostic
Trouble Codes”

Result:

All injectors are OK.

Proceed to Test Step 8.

8. Individual Malfunctioning Cylinders

A. With the engine speed at a fast idle, use the electronic service
tool to perform the manual

“

Cylinder Cut Out Test

”

. As each cylin-

der is cut out, listen for a change in the sound from the engine.
When a cylinder is cut out, there should be a noticeable change in
the sound of the engine.

Cylinders

Result:

There is not a noticeable change in the sound of

the engine for at least one cylinder.

Investigate the cause of the fault on any cylinder that is not
operating. Investigate the cause of the fault on any cylin-
der that is operating below normal performance.

Result:

There is a noticeable change in the sound of the

engine for each cylinder.

Contact the Dealer Solution Network (DSN).

i05271038

Engine

Overspeeds

This procedure covers the following diagnostic code:

Table 29

Diagnostic Trouble Codes for the Engine Pressure Sensors

J1939

Code

Description

Notes

190-15

Engine Speed : High -
least severe (1)

The Electronic Control Module (ECM) detects that the engine speed has exceeded 3100 rpm for at least
5 seconds.

If equipped, the warning lamp will flash.

The Electronic Control Module (ECM) limits the flow
of fuel in order to prevent the engine speed from
exceeding the maximum rpm. When the engine
speed has dropped to less than the maximum rpm,
the engine overspeed diagnostic code will be reset.

The following operating conditions can cause the
engine speed to exceed this value:

• On a mobile machine, an incorrect transmission

gear is selected.

• Use of an incorrect fuel

• Combustible gases in the air inlet for the engine

If the engine speed exceeds the maximum rpm, the
ECM illuminates the warning lamp and an engine
overspeed diagnostic code is logged. No
troubleshooting is required.

The history of engine overspeeds can be viewed on
the electronic service tool.

i06003891

Engine Shutdown Occurs
Intermittently

Note:

Use this procedure only if the engine shuts

down completely and the engine must be restarted.

70

UENR0612

Symptom Troubleshooting

This document has been printed from SPI2. NOT FOR RESALE

«
...
68
69
70
71
72
...
»

Содержание 854E-E34TA





























































































































































































































































Отзывы:

Нет отзывов