Perkins 5006A-E23TA Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 100

Perkins 5006A-E23TA Скачать руководство пользователя страница 62

Drain

Pressurized System: Hot coolant can cause seri-
ous burns. To open the cooling system filler cap,
stop the engine and wait until the cooling system
components are cool. Loosen the cooling system
pressure cap slowly in order to relieve the

pressure.

Illustration 48

g06258066

Typical example

Illustration 49

g06258129

Typical example

Illustration 50

g06258092

Typical example

1.

Stop the engine and allow the engine to cool.

Isolate the electrical supply to the engine. Loosen
the cooling system filler cap (1) slowly to relieve
any pressure. Remove the cooling system filler
cap.

2.

Clean the cooling system filler cap (1) and inspect

the seal (2). If the seal is damaged, discard the old
filler cap and install a new filler cap. If the seal is
not damaged, use a suitable pressurizing pump to
pressure test the filler cap. The correct pressure is
stamped on the face of the filler cap. If the filler
cap does not retain the correct pressure, replace
the filler cap.

3.

Open the drain cock or remove the drain plug (3)

on the radiator .

62

M0122761

Maintenance Section
Cooling System Coolant (ELC) - Change

«
...
60
61
62
63
64
...
»

Содержание 5006A-E23TA





































































































Отзывы:

Нет отзывов