PerkinElmer Spotlight 400 Series Скачать руководство пользователя страница 109

Страница: 109 / 120

Appendices . 109

Select

PerkinElmer SpectrumIMAGE

in the list of programs.

Click

Remove

(Windows XP) or

Uninstall

(Windows 7).

The SpectrumIMAGE software is uninstalled, and you are prompted to restart your

system.

NOTE: The C:\Windows\pelimage.ini file is not removed. This allows a new SpectrumIMAGE

installation to preserve settings from the old.

Installing the SpectrumIMAGE software

NOTE: Before installing SpectrumIMAGE, read and print the release notes which can be

found as a .rtf file at the root of the

SpectrumIMAGE Software DVD

. These notes

contain important information that may not be in this User's Guide or the on-screen

Help.

After uninstalling any existing SpectrumIMAGE software:

Close all open or minimized software windows.

Insert the SpectrumIMAGE DVD.
If the DVD does not run automatically, click

Start

and then

Run

. Click

Browse

, select

the

SpectrumIMAGE

DVD, and then

setup.exe

. Click

Open

and then

After the installation files are prepared, the InstallShield Wizard is displayed.

Click

Next

The License Agreement page is displayed.

Содержание Spotlight 400 Series

























































































































Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Spotlight 400 Series, Руководство пользователя

Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Бренды по названию

Популярные бренды