PerkinElmer Spotlight 400 Series Скачать руководство пользователя страница 108

Страница: 108 / 120

108 . Spotlight 400 Series User’s Guide

Appendix 1: Installing SpectrumIMAGE

Software

NOTE: Spectrum software must be installed BEFORE you start to install SpectrumIMAGE.

CAUTION

If your Spotlight system appears to be faulty, consult a PerkinElmer

Service Engineer.

Do not attempt to remedy the problem by re-installing the

SpectrumIMAGE software. Important setup or diagnostic information

could be lost.

You may need to install a later version of the SpectrumIMAGE software if, for example, you

have purchased an accessory that is not supported by the software installed on your PC.

CAUTION

Check the documentation supplied with the accessory to make sure that

it is compatible with your Spotlight imaging system.

If you believe a hardware or firmware upgrade may be required, consult

a PerkinElmer Service Engineer.

Before installing the SpectrumIMAGE software, you must uninstall any existing

SpectrumIMAGE software.

Uninstalling an earlier version of SpectrumIMAGE

software

CAUTION

Before you begin, copy the C:\WINDOWS\pelimage.ini file to a safe

location on your PC hard drive and to a memory stick.

These backups ensure that, if necessary, the initialization settings for

your Spotlight system can be recovered by a PerkinElmer Service

Engineer.

NOTE: You must be logged in at Administrator level in Windows before uninstalling or

installing software.

If you have not done so already, copy the

C:\Windows\pelimage.ini

file to a safe

location on your hard drive and to a memory stick.

Display the Control Panel, and then select

Add/Remove Programs

(Windows XP) or

Programs and Features

(Windows 7).

Содержание Spotlight 400 Series

























































































































Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Spotlight 400 Series, Руководство пользователя

Результаты поиска

Содержание Spotlight 400 Series

Отзывы:

Бренды по названию

Популярные бренды