PerkinElmer Raman Flex 400 Series Скачать руководство пользователя страница 64

Страница: 64 / 74

64 . RamanFlex 400 Series Getting Started Guide

Additional Parts and Upgrades

Safety and Calibration

Part

Number

Description

L1320262

Raman Laser Safety Kit (785 nm)

Contains external interlock cable, laser glasses, laser detection card, and door

warning label

L1320237

Raman Calibration Kit (785 nm)

Contains neon lamp and fiber optic connector (for wavelength calibration),

calibration plate containing polystyrene (for wavelength calibration verification

and laser wavelength calibration), calcite (for resolution verification), and NIST

2241 Intensity Correction Standard

L1321831

NIST 2241 Relative Intensity Correction SRM

L1323503

Replacement laser keys

L1323518

Laser Glasses

Fiber Optic Probes

Part

Number

Description

L1320002

Raman fiber optic probe, 7.5 mm working distance, maximum working

temperature 80 °C, 5 m cabling

L1320003

Liquid immersion sleeve for Raman fiber optic probe

Raman probe – long, 350 mm long, suitable for non-contact and liquid

immersion. Maximum working temperature 200 °C, maximum working

pressure 1500 psi, 5 m cabling

Raman probe – max, suitable for non-contact and liquid immersion. Maximum

working temperature 500 °C, maximum working pressure 3000 psi, 5 m

cabling

Purge Jacket for Raman probe – max, required to enable max probe operation

at temperatures between 200 °C and 500 °C

L1320030

Raman triggered probe, 7.5 mm working distance, maximum working

temperature 80 °C, 5 m cabling

L1320031

Raman triggered probe, 7.5 mm working distance, maximum working

temperature 80 °C, 20 m cabling

L1320070

Short immersion sleeve (10 cm) – for use with L1320030 and L1320031

Содержание Raman Flex 400 Series











































































Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Raman Flex 400 Series, Руководство по началу работы

Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды