PerkinElmer Raman Flex 400 Series Скачать руководство пользователя страница 61

Страница: 61 / 74

Using the RamanFlex 400 Series . 61

Select

The Frequency Calibration dialog is displayed.

Ensure that you have followed the instructions on the dialog, and then click

Next

The instrument will now perform the laser frequency calibration routine. This will take a

few minutes. At the end of the calibration, the result is displayed.
In the unlikely event that the laser frequency calibration routine should fail, please

perform a wavelength calibration and repeat the laser frequency calibration.

NOTE: If the calibration fails again, please contact your PerkinElmer Service Representative.

SOP-10: Intensity Calibration

The intensity calibration must be performed using the National Institute of Standards and

Technology (NIST) Standard Reference Material. NIST SRM 2241 is the relative intensity

correction standard for Raman spectroscopy when using 785 nm excitation.

NOTE: NIST calibration is temperature dependent. If you intend to perform quantitative

analyses, you should ensure that your instrument is NIST calibrated at the

temperature at which data is to be acquired. Otherwise, any data should be used for

qualitative analyses only.

The NIST intensity correction is valid in the recommended operating temperature

range 20

C – 25

C. If you move the instrument to an environment outside this

temperature range, that is 15

C – 20

C or 25

C – 30

C, we recommend that you

perform a NIST intensity correction at this new temperature.

Contact your PerkinElmer Raman Business Unit if you wish to set up a NIST intensity

correction for a different temperature range.

Intensity calibration should typically be performed on an annual basis – that is, during an

annual instrument service – but also whenever the instrument is moved, following a service

repair, or when there has been significant temperature variation in the local environment.

NOTE: As intensity calibration is not required on a regular basis, NIST Standards are not

included in the basic RamanFlex 400 package. Standard Reference Materials can be

purchased from PerkinElmer (part number L1321831). Your instrument will be

intensity calibrated prior to shipping or during installation.

NOTE: If you have a RamanFlex 400F with two fiber optic probes, you must perform an

intensity calibration on both fiber optic probes.

Содержание Raman Flex 400 Series











































































Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer Raman Flex 400 Series, Руководство по началу работы

Результаты поиска

Содержание Raman Flex 400 Series

Отзывы:

Бренды по названию

Популярные бренды