PerkinElmer OilExpress System Скачать руководство пользователя страница 92

Страница: 92 / 102

92 . OilExpress System User's Guide

Spares and Consumables

Item

PerkinElmer Part Number

Matched pair of ZnSe Windows for flowcell

L1191081

Replacement Gasket and Spacer Set for flowcell

L1191082

Sample Rack (4 oz)

L1200551

Syringe (10 ml)

L1200552

Seal Kit (10 ml) for syringe plunger

L1200553

Valve 3-port

L1200554

Needle

L1200555

Pump to Solvent Tubing (2)

L1200556

Injection/Wash Port to Cell Tube

L1200557

Lubrication Kit

L1200559

Waste Tubing

L1200560

Plunger Screw

L1200571

Syringe Clamp

L1200574

RS232 Cable

L1200576

Wash Station Mounting Plate

L1200577

Protective Shield

L1200579

Consumables Kit

L1200581

Injection Port

L1200586

Solvent Bottle and Cap (drilled)

L1195019

Syringe Pump to Cell Tubing

L1200585

Syringe Pump to Needle Tubing

L1200587

Pack of 6, 16-position Racks for Test tube Vials

L1200589

Torque Driver 10 – 120 cNm

L9003631

Hex Bit 3.0 mm (for use with L9003631)

L9003632

Содержание OilExpress System







































































































Результаты поиска

Содержание OilExpress System

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer OilExpress System, Руководство пользователя

Результаты поиска

Содержание OilExpress System

Отзывы:

Бренды по названию

Популярные бренды